s13 trans. in s14- I searched... sticky it? - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

gotta240 · 07-29-2007, 04:34 PM

First- i searched. Found a few saying that the s13 trans. can be used in s14, but the CAS is lacking. GOT IT. It would be nice to get an entire fact thread on the trans. differences and what can be done to avoid a CEL in a sticky. I see ton's of threads asking if it will work, but nothing more specific than YES.

My question is- What exactly needs to/can be done to use a s13 trans.(and s13 bellhousing) on a obd1 s14 WITHOUT THROWING A CODE? Also, does anyone know what all the extra sensors are, and what can/can't be used?

The s13 trans is on the car and only ONE sensor from my s14 harness plugs in. There are about 3 or 4 other tranny plugs which won't connect to anywhere on the trans. Can i just take sensors off a s14 trans. and connect them to the s13 trans, or does it not work like that?

Thanks .

na3j nitsuj · 07-29-2007, 05:40 PM

this can probably answer some of ur questions.

http://www.240sx.org/links/installs/s14_5speed_swap.htm

I am also planning on swapping my s14 to 5speed.

goodluck!

aznrib · 07-29-2007, 09:09 PM

http://www.nicoclub.com/articles.php?id=210410

this link is more descriptive.

The sensors will have to be wired manually. You mainly need the reverse harness wired up. You will also have to get a S14 speed sensor if you are using a S13 tranny. For the CAS you can drill a hole on the flat part of the bell housing.

I believe if the CAS is not connected, you will throw codes but I'm not too sure.

07-29-2007, 04:34 PM	#1
gotta240 Post Whore! Join Date: Dec 2005 Location: so cal Posts: 3,496 Trader Rating: (21) Feedback Score: 21 reviews	s13 trans. in s14- I searched... sticky it? First- i searched. Found a few saying that the s13 trans. can be used in s14, but the CAS is lacking. GOT IT. It would be nice to get an entire fact thread on the trans. differences and what can be done to avoid a CEL in a sticky. I see ton's of threads asking if it will work, but nothing more specific than YES. My question is- What exactly needs to/can be done to use a s13 trans.(and s13 bellhousing) on a obd1 s14 WITHOUT THROWING A CODE? Also, does anyone know what all the extra sensors are, and what can/can't be used? The s13 trans is on the car and only ONE sensor from my s14 harness plugs in. There are about 3 or 4 other tranny plugs which won't connect to anywhere on the trans. Can i just take sensors off a s14 trans. and connect them to the s13 trans, or does it not work like that? Thanks .

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-29-2007, 05:40 PM	#2
na3j nitsuj Zilvia Member Join Date: Jul 2006 Location: Bay Area Posts: 194 Trader Rating: (0) Feedback Score: 0 reviews	this can probably answer some of ur questions. http://www.240sx.org/links/installs/s14_5speed_swap.htm I am also planning on swapping my s14 to 5speed. goodluck!

07-29-2007, 09:09 PM	#3
aznrib Zilvia Member Join Date: Nov 2005 Location: Edison Posts: 248 Trader Rating: (2) Feedback Score: 2 reviews	http://www.nicoclub.com/articles.php?id=210410 this link is more descriptive. The sensors will have to be wired manually. You mainly need the reverse harness wired up. You will also have to get a S14 speed sensor if you are using a S13 tranny. For the CAS you can drill a hole on the flat part of the bell housing. I believe if the CAS is not connected, you will throw codes but I'm not too sure.