What Now?!?! - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

tiki240 · 07-19-2003, 07:49 PM

OK this swap is killing me. the driver side motor mount bracket is bent. i removed it with the remnents of the old motor mounts for the SR. The KA bracket will only line up on the bottom and not the two top holes under the turbo. do you think cutting the KA bracket to just suit the bottom two holes will be alright? i have 3 days to finish before car get towed. any ideas?!??? help im desparate. and when i say bent i mean i can even get the old motor mount nut off because of the way its bent. its pretty thick so i dunno how i would bend it back. HELP

tiki240 · 07-19-2003, 08:45 PM

anyone??

Bill Roberts · 07-19-2003, 09:37 PM

Get a handheld tank torch for brazing and heat that bolt up cherry hot and you can have your way with it..careful, cherry hot iron is 1400 degrees.

If you smoke the rubber in the mount, who cares! 3M has a spray that you can rebuild it with.

You need a machinest to be with you if you can't fabricate an adapter plate.

*transient* · 07-19-2003, 09:50 PM

Hehe, careful though, if you smoke the rubber too much you'll get some nice dampening fluid in your face.

Muzzy · 07-20-2003, 12:40 AM

how the he!! did u bend it??

Fibercus · 07-20-2003, 12:42 AM

my guess was a forklift, when they were moving it around (place where you purchased motorset)

what you guys think?

Muzzy · 07-20-2003, 12:47 AM

oops...misread...but the rubber motor mount or the part that connects to the motor mount???

tiki240 · 07-20-2003, 08:12 AM

its the part that connects to the engine block

tiki240 · 07-20-2003, 08:14 AM

another

einherjar · 07-20-2003, 04:23 PM

honestly if that was me i'd smash it back with a hammer.

07-19-2003, 07:49 PM	#1
tiki240 Zilvia Member Join Date: May 2003 Location: Y-town VA Age: 40 Posts: 179 Trader Rating: (0) Feedback Score: 0 reviews	What Now?!?! OK this swap is killing me. the driver side motor mount bracket is bent. i removed it with the remnents of the old motor mounts for the SR. The KA bracket will only line up on the bottom and not the two top holes under the turbo. do you think cutting the KA bracket to just suit the bottom two holes will be alright? i have 3 days to finish before car get towed. any ideas?!??? help im desparate. and when i say bent i mean i can even get the old motor mount nut off because of the way its bent. its pretty thick so i dunno how i would bend it back. HELP __________________ Iridium V

07-19-2003, 08:45 PM	#2
tiki240 Zilvia Member Join Date: May 2003 Location: Y-town VA Age: 40 Posts: 179 Trader Rating: (0) Feedback Score: 0 reviews	gfd anyone?? __________________ Iridium V

07-19-2003, 09:50 PM	#4
transient Premium Member Join Date: Jun 2001 Location: Los Angeles, California Age: 41 Posts: 2,947 Trader Rating: (0) Feedback Score: 0 reviews	Hehe, careful though, if you smoke the rubber too much you'll get some nice dampening fluid in your face. __________________ Learn everything you can, while you still have the chance.

07-20-2003, 12:40 AM	#5
Muzzy Zilvia FREAK! Join Date: Jan 2003 Location: TX Posts: 1,555 Trader Rating: (0) Feedback Score: 0 reviews	how the he!! did u bend it?? __________________ lemme have a dollar

07-20-2003, 12:42 AM	#6
Fibercus BANNED Join Date: Jul 2001 Location: Canyon Country, CA Age: 44 Posts: 714 Trader Rating: (0) Feedback Score: 0 reviews	my guess was a forklift, when they were moving it around (place where you purchased motorset) what you guys think? Last edited by Fibercus; 07-20-2003 at 12:45 AM..

07-19-2003, 09:37 PM	#3
Bill Roberts Zilvia FREAK! Join Date: May 2003 Location: S FL. Posts: 1,538 Trader Rating: (0) Feedback Score: 0 reviews	Get a handheld tank torch for brazing and heat that bolt up cherry hot and you can have your way with it..careful, cherry hot iron is 1400 degrees. If you smoke the rubber in the mount, who cares! 3M has a spray that you can rebuild it with. You need a machinest to be with you if you can't fabricate an adapter plate.

07-20-2003, 12:47 AM	#7
Muzzy Zilvia FREAK! Join Date: Jan 2003 Location: TX Posts: 1,555 Trader Rating: (0) Feedback Score: 0 reviews	oops...misread...but the rubber motor mount or the part that connects to the motor mount??? __________________ lemme have a dollar

07-20-2003, 04:23 PM	#10
einherjar Zilvia Member Join Date: Jun 2003 Location: Ontario Posts: 179 Trader Rating: (0) Feedback Score: 0 reviews	honestly if that was me i'd smash it back with a hammer.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode