s13 Running Rough - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Exiled 240 · 05-26-2011, 10:16 PM

Alright so i bought my 89 240sx a few months ago and it has always been running rough. it doesnt start all of the time and it idles rough (normally around 1250rpm-2000rpm). when you rev the engine it sputters and sounds like it is about to stall. now i was just gunna forget about fixing this motor and just rebuild the ka24de i have in my garage but the parts will be awhile till they r available.

Does anyone have an idea on what would cause this issue?

Not sure if this matters at all but whenever i disconnect the MAF it idles normal but stalls when ever i try going anywhere.

Thanks for the help

BestOneLeft · 05-26-2011, 10:17 PM

Id try the maf first, At least clean it with some brake cleaner/starter fluid

Exiled 240 · 05-26-2011, 10:19 PM

Srry should have stated that i did clean it with MAF sensor cleaner. im hoping the whole sensor isnt bad

NIZzS13 · 05-27-2011, 12:38 AM

You had the answer from the begining when u said it idles normal with the maf disconnected. MAF is no good, its idles ok because the computer is pre programmed to know how much air is coming in at idle and the amount of fuel to use, but once u open the throttle it no longer knows how much gas to add so it quickly dumps fuel cause the car to stall. Also check for intake leaks after the MAF sensor. But if you have no leaks then the sensor is garbage. Cleaning them only works 50% of the time.

Exiled 240 · 05-27-2011, 05:19 AM

Alright kool. Then I guess it is time for a new MAF and hopefully I can get the car running for awhile till the rebuild parts are available.

05-26-2011, 10:16 PM	#1
Exiled 240 Zilvia Junkie Join Date: Mar 2011 Location: Grand Rapids, MI Age: 34 Posts: 321 Trader Rating: (4) Feedback Score: 4 reviews	s13 Running Rough Alright so i bought my 89 240sx a few months ago and it has always been running rough. it doesnt start all of the time and it idles rough (normally around 1250rpm-2000rpm). when you rev the engine it sputters and sounds like it is about to stall. now i was just gunna forget about fixing this motor and just rebuild the ka24de i have in my garage but the parts will be awhile till they r available. Does anyone have an idea on what would cause this issue? Not sure if this matters at all but whenever i disconnect the MAF it idles normal but stalls when ever i try going anywhere. Thanks for the help

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-26-2011, 10:17 PM	#2
BestOneLeft Join Date: May 2011 Location: SOCAL Age: 38 Posts: 45 Trader Rating: (0) Feedback Score: 0 reviews	Id try the maf first, At least clean it with some brake cleaner/starter fluid

05-26-2011, 10:19 PM	#3
Exiled 240 Zilvia Junkie Join Date: Mar 2011 Location: Grand Rapids, MI Age: 34 Posts: 321 Trader Rating: (4) Feedback Score: 4 reviews	Srry should have stated that i did clean it with MAF sensor cleaner. im hoping the whole sensor isnt bad

05-27-2011, 12:38 AM	#4
NIZzS13 Leaky Injector Join Date: Jan 2008 Location: Bronx, NY Posts: 114 Trader Rating: (0) Feedback Score: 0 reviews	You had the answer from the begining when u said it idles normal with the maf disconnected. MAF is no good, its idles ok because the computer is pre programmed to know how much air is coming in at idle and the amount of fuel to use, but once u open the throttle it no longer knows how much gas to add so it quickly dumps fuel cause the car to stall. Also check for intake leaks after the MAF sensor. But if you have no leaks then the sensor is garbage. Cleaning them only works 50% of the time.

05-27-2011, 05:19 AM	#5
Exiled 240 Zilvia Junkie Join Date: Mar 2011 Location: Grand Rapids, MI Age: 34 Posts: 321 Trader Rating: (4) Feedback Score: 4 reviews	Alright kool. Then I guess it is time for a new MAF and hopefully I can get the car running for awhile till the rebuild parts are available.