Crankshaft position sensor sub-harness location? (pic) - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

kanekz · 03-10-2004, 04:38 PM

Well my tach is not working right. Sputters to 2k max at times but mostly stays idle. Was told to check the crankshaft position sensor. FSM says to unplug the sub harness. I looked I cant even find the harness on my S14. The closest things is a purple connector but i dont think thats it. not sure what exactly is causing tach problem though.

Attached Pic is from FSM showing sub harness location

kanekz · 03-11-2004, 05:32 PM

Anyone??? I really want to get my tach working. If you drive a S14, please check and tell me if you see it. Thanks!

96twofourty · 03-11-2004, 07:01 PM

the sensor is on the top of the bell housing if that helps

Tictakman · 03-11-2004, 08:36 PM

ya its at the top of the bell housing...u can see it from the header side. if im correct there is an extention harness that hooks into that sensor. just jack up ur car and it should be on the clutch fork side.

Zak

DuffMan · 03-11-2004, 08:42 PM

If the crank pos sensor was that faulty that you couldnt even get a good tach signal, your engine wouldnt run. Thats not your problem.

kanekz · 03-11-2004, 09:14 PM

Yea I know where the sensore is. I finally found the sub-harness. It was under the car all the way below the EGR valve.

Duffman, you acutally gave me the answer that I am lookin for. But, when you say good, do you mean ANY signal at all?? So does this mean probably mean that I need a new gauge cluster/tach?

03-11-2004, 05:32 PM	#2
kanekz Zilvia Addict Join Date: May 2002 Location: California Posts: 802 Trader Rating: (0) Feedback Score: 0 reviews	Anyone??? I really want to get my tach working. If you drive a S14, please check and tell me if you see it. Thanks! __________________ Blitz!!

03-11-2004, 09:14 PM	#6
kanekz Zilvia Addict Join Date: May 2002 Location: California Posts: 802 Trader Rating: (0) Feedback Score: 0 reviews	Yea I know where the sensore is. I finally found the sub-harness. It was under the car all the way below the EGR valve. Duffman, you acutally gave me the answer that I am lookin for. But, when you say good, do you mean ANY signal at all?? So does this mean probably mean that I need a new gauge cluster/tach? __________________ Blitz!! Last edited by kanekz; 03-11-2004 at 09:49 PM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-11-2004, 07:01 PM	#3
96twofourty Zilvia Junkie Join Date: Oct 2003 Location: nor*cal Posts: 354 Trader Rating: (0) Feedback Score: 0 reviews	the sensor is on the top of the bell housing if that helps

03-11-2004, 08:36 PM	#4
Tictakman Zilvia Junkie Join Date: Oct 2002 Posts: 321 Trader Rating: (0) Feedback Score: 0 reviews	ya its at the top of the bell housing...u can see it from the header side. if im correct there is an extention harness that hooks into that sensor. just jack up ur car and it should be on the clutch fork side. Zak

03-11-2004, 08:42 PM	#5
DuffMan Post Whore! Join Date: Oct 2001 Location: in a cardboard box Posts: 2,517 Trader Rating: (0) Feedback Score: 0 reviews	If the crank pos sensor was that faulty that you couldnt even get a good tach signal, your engine wouldnt run. Thats not your problem.