NV Complete RB20DET w/5spd, Mckinney mounts, KA D/S ++ - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

GenPac · 01-18-2012, 07:43 PM

Removed the RB20DET in favor of more litres and less snail. I'm looking to get $1500 for everything, but I am willing to deal a bit if it all goes at once.

The RB20DET has had the following replaced with OE parts: Timing set (belt, idler pulley, tensioner pulley), Head gasket, Upper and Lower intake gaskets, Exhaust manifold gasket and manifold studs/nuts/washers, Water pump and thermostat, Cam cover gaskets and grommets... I'm sure I'm leaving some things out.
Other stuff done:
installed ARP headstuds, have a custom heatshield for the turbo/mani and header wrap on the manifold and elbow.
Trans has a Trust shift knob on it because I couldn't get it loose. OEM KA 5spd driveshaft as well, if needed. McKinney basic mounts, ECU, J60 MAF, S13/RB harness, Large 3x11x30 intercooler with RB20 piping, Clutch slave and kevlar clutch line, Downpipe w/WB bung, manual boost controller, ect. I'm sure I am forgetting somethings.

Essentially, it's all there, already refreshed with what's recommended when you buy from an importer. I am not interested in shipping this, at this time!

For now, I'd like to sell complete but might be willing to part out if there's no interest as a single sale.

I can be reached at 702-577-7653, text preferably. Or PMs on here.

PICS:

installed pic:

obligatory car pic:

GenPac · 01-19-2012, 04:24 PM

Not really a bump, but I do have a local buyer. As for now this is spoken for.

rbeast · 01-19-2012, 07:30 PM

just a quick question, i dont mean to jack your thread or anything. how did you mount the fmic? people have told me i'll need to remove the steel bumper reinforcment....

GenPac · 01-19-2012, 08:59 PM

Quote:

Originally Posted by rbeast

just a quick question, i dont mean to jack your thread or anything. how did you mount the fmic? people have told me i'll need to remove the steel bumper reinforcment....

That's correct. Remove it or run a much smaller IC.

Danielmcn · 01-19-2012, 09:45 PM

Or cut into the support a little..

GenPac · 01-20-2012, 11:16 PM

This is sold. Please close!

01-18-2012, 07:43 PM	#1
GenPac Leaky Injector Join Date: Jul 2010 Location: Las Vegas Age: 46 Posts: 84 Trader Rating: (5) Feedback Score: 5 reviews	Complete RB20DET w/5spd, Mckinney mounts, KA D/S ++ Removed the RB20DET in favor of more litres and less snail. I'm looking to get $1500 for everything, but I am willing to deal a bit if it all goes at once. The RB20DET has had the following replaced with OE parts: Timing set (belt, idler pulley, tensioner pulley), Head gasket, Upper and Lower intake gaskets, Exhaust manifold gasket and manifold studs/nuts/washers, Water pump and thermostat, Cam cover gaskets and grommets... I'm sure I'm leaving some things out. Other stuff done: installed ARP headstuds, have a custom heatshield for the turbo/mani and header wrap on the manifold and elbow. Trans has a Trust shift knob on it because I couldn't get it loose. OEM KA 5spd driveshaft as well, if needed. McKinney basic mounts, ECU, J60 MAF, S13/RB harness, Large 3x11x30 intercooler with RB20 piping, Clutch slave and kevlar clutch line, Downpipe w/WB bung, manual boost controller, ect. I'm sure I am forgetting somethings. Essentially, it's all there, already refreshed with what's recommended when you buy from an importer. I am not interested in shipping this, at this time! For now, I'd like to sell complete but might be willing to part out if there's no interest as a single sale. I can be reached at 702-577-7653, text preferably. Or PMs on here. PICS: installed pic: obligatory car pic:

01-19-2012, 04:24 PM	#2
GenPac Leaky Injector Join Date: Jul 2010 Location: Las Vegas Age: 46 Posts: 84 Trader Rating: (5) Feedback Score: 5 reviews	Not really a bump, but I do have a local buyer. As for now this is spoken for.

01-19-2012, 07:30 PM	#3
rbeast Leaky Injector Join Date: Nov 2011 Location: Jacksonville Age: 32 Posts: 142 Trader Rating: (6) Feedback Score: 6 reviews	just a quick question, i dont mean to jack your thread or anything. how did you mount the fmic? people have told me i'll need to remove the steel bumper reinforcment....

01-19-2012, 09:45 PM	#5
Danielmcn Leaky Injector Join Date: May 2011 Location: wilson nc Age: 40 Posts: 117 Trader Rating: (0) Feedback Score: 0 reviews	Or cut into the support a little..

01-20-2012, 11:16 PM	#6
GenPac Leaky Injector Join Date: Jul 2010 Location: Las Vegas Age: 46 Posts: 84 Trader Rating: (5) Feedback Score: 5 reviews	This is sold. Please close!