IA Fully Built Sr20det *Turn Key* - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

07kyeringt · 05-13-2013, 02:58 PM

Hey all. I Have purchased a LS1 I am swapping into my s14 for next year MDU season. So I no longer need my sr20det. It is a very awesome motor. Runs amazing. I can take video for you all or it is still in car so you can come check it out either or.

This will be a full drop in swap for new buyer. will even come with aluminum driveshaft and exhaust.

Motor has approx. 6000 miles since rebuild. I am asking for $5200.00 for everything. drop in turn key swap.

I am looking to sell as a package if there are things you dont want you can sell them after purchase. I will consider parting out if there is no interest in whole set and most parts are accounted for.

History.. I bought this about a year ago from Mike Pollard. He swapped it out with his 2.2 liter sr20det he is still running for formula drift.

Engine-
Wiseco pistons
Manly rods
ACL bearings
ARP main and head studs
New Oil pump, timing chain and guides
Tomei Head gasket
BC Valve springs and retainers
BC 272 cams
JUN exhaust valve guides & Oversized valves
Tomei Rocker arm stoppers

Bolt-ons-
Greddy oil pan
Aftermarket intake plenum (bypassed IACV)
Sard 850cc injectors
Z32 MAF
ORC Super Single 409 Clutch kit
Avid Mounts
Isis exhaust manifold
Isis rs3871 turbo
Megan down turbo elbow and Dp
Isis blast pipes (4”)
Wiring specialties harness
Enthalpy tuned ECU
Driveshaft shop Aluminum DS
Custom front mount IC setup
Circuit sports catch can
Greddy BOV
Lightweight pulley
Tomei Fuel pressure regulator
New Isis starter

Transmission - sr20det 5-speed Perfect condition. No grinds no problems whatsoever.

Might be some things Im forgetting. Motor is awesome. In car if proof that it runs is needed.
I am located in cedar rapids, IA @ 319-210-3893 I have some ppl on here who can vouch for quality as well.

Here are some pics.

this was before painting intake mani and valve cover but it shows you mid mount.

clutch you will get with motor

under valve cover

Again asking for $5200.00 for EVERYTHING

Help me get this V8 ready before next season. Open to trades and cash for anything that may help with lsx swap.

07kyeringt · 05-14-2013, 07:20 AM

Bump. Willing to part if I can get some good interest. Open to offers for entire set also. Let me know!

Maverick06xx · 05-14-2013, 07:40 AM

Hey i'm interested if you are willing to part out as i'm only interested in the long block. I have a built head and a built long block but my block is at the machine shop getting looked out since its been sitting for 4 years and has some rust in 2 cylinders and they are taking a bit long with it. Do u have any receipts on parts, labor and the shop who assembled motor? Well i guess if you are willing to part it out, let me know thanks

~Maverick06xx~

05-13-2013, 02:58 PM	#1
07kyeringt Zilvia Member Join Date: Apr 2010 Location: Iowa Age: 35 Posts: 200 Trader Rating: (11) Feedback Score: 11 reviews	Fully Built Sr20det Turn Key Hey all. I Have purchased a LS1 I am swapping into my s14 for next year MDU season. So I no longer need my sr20det. It is a very awesome motor. Runs amazing. I can take video for you all or it is still in car so you can come check it out either or. This will be a full drop in swap for new buyer. will even come with aluminum driveshaft and exhaust. Motor has approx. 6000 miles since rebuild. I am asking for $5200.00 for everything. drop in turn key swap. I am looking to sell as a package if there are things you dont want you can sell them after purchase. I will consider parting out if there is no interest in whole set and most parts are accounted for. History.. I bought this about a year ago from Mike Pollard. He swapped it out with his 2.2 liter sr20det he is still running for formula drift. Engine- Wiseco pistons Manly rods ACL bearings ARP main and head studs New Oil pump, timing chain and guides Tomei Head gasket BC Valve springs and retainers BC 272 cams JUN exhaust valve guides & Oversized valves Tomei Rocker arm stoppers Bolt-ons- Greddy oil pan Aftermarket intake plenum (bypassed IACV) Sard 850cc injectors Z32 MAF ORC Super Single 409 Clutch kit Avid Mounts Isis exhaust manifold Isis rs3871 turbo Megan down turbo elbow and Dp Isis blast pipes (4”) Wiring specialties harness Enthalpy tuned ECU Driveshaft shop Aluminum DS Custom front mount IC setup Circuit sports catch can Greddy BOV Lightweight pulley Tomei Fuel pressure regulator New Isis starter Transmission - sr20det 5-speed Perfect condition. No grinds no problems whatsoever. Might be some things Im forgetting. Motor is awesome. In car if proof that it runs is needed. I am located in cedar rapids, IA @ 319-210-3893 I have some ppl on here who can vouch for quality as well. Here are some pics. this was before painting intake mani and valve cover but it shows you mid mount. clutch you will get with motor under valve cover Again asking for $5200.00 for EVERYTHING Help me get this V8 ready before next season. Open to trades and cash for anything that may help with lsx swap.

05-14-2013, 07:40 AM	#3
Maverick06xx Leaky Injector Join Date: May 2013 Location: NC Posts: 68 Trader Rating: (0) Feedback Score: 0 reviews	Built sr Hey i'm interested if you are willing to part out as i'm only interested in the long block. I have a built head and a built long block but my block is at the machine shop getting looked out since its been sitting for 4 years and has some rust in 2 cylinders and they are taking a bit long with it. Do u have any receipts on parts, labor and the shop who assembled motor? Well i guess if you are willing to part it out, let me know thanks ~Maverick06xx~

05-14-2013, 07:20 AM	#2
07kyeringt Zilvia Member Join Date: Apr 2010 Location: Iowa Age: 35 Posts: 200 Trader Rating: (11) Feedback Score: 11 reviews	Bump. Willing to part if I can get some good interest. Open to offers for entire set also. Let me know!