bracket to mount single cam AC comp on SR - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

TJElite · 02-08-2007, 09:14 AM

I've seen mention of these on other forums, but have never actually seen one. Does anyone know of a source for the bracket to mount a single cam AC compressor onto an SR? I'm dropping one in to a 94 hardbody pickup, formerly single cam. The truck has a practically new, fully charged and working, AC system, that I'd rather not break down and rebuild if I can avoid it.

Any leads are appreciated.

Toby

*ManoNegra* · 02-08-2007, 03:25 PM

Seen them but they've been custom one of deals. As far as I know, no one mass produces them. I tried talking a buddy that works at a machine shop into making them but he's a pothead and I'm too lazy = fail.

Another solution would be to use the SR pump and have the lines spliced by a willing and competent AC shop, then recharge the system. There is one here in Gardena that does it - I know, lot of help that'd do you.

Good luck.

TJElite · 02-09-2007, 08:31 AM

Thanks. I've already looked at the SR comp route, and that's definitely an option. It would just be nice to use what I already have, that works.

I figured the brackets would be limited production, at best, I was just hoping someone either had them for sale, or had at least gone down this road before, and could share the design.

Toby

02-08-2007, 09:14 AM	#1
TJElite Join Date: Aug 2005 Location: Oldsmar, FL Posts: 5 Trader Rating: (0) Feedback Score: 0 reviews	bracket to mount single cam AC comp on SR I've seen mention of these on other forums, but have never actually seen one. Does anyone know of a source for the bracket to mount a single cam AC compressor onto an SR? I'm dropping one in to a 94 hardbody pickup, formerly single cam. The truck has a practically new, fully charged and working, AC system, that I'd rather not break down and rebuild if I can avoid it. Any leads are appreciated. Toby __________________ Toby Johnson T&J Elite Customs, Inc. 101 Pine Ave. S Oldsmar, FL 34677 813-818-8956 www.tjelitecustoms.com [email protected]

02-09-2007, 08:31 AM	#3
TJElite Join Date: Aug 2005 Location: Oldsmar, FL Posts: 5 Trader Rating: (0) Feedback Score: 0 reviews	Thanks. I've already looked at the SR comp route, and that's definitely an option. It would just be nice to use what I already have, that works. I figured the brackets would be limited production, at best, I was just hoping someone either had them for sale, or had at least gone down this road before, and could share the design. Toby __________________ Toby Johnson T&J Elite Customs, Inc. 101 Pine Ave. S Oldsmar, FL 34677 813-818-8956 www.tjelitecustoms.com [email protected]

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-08-2007, 03:25 PM	#2
ManoNegra Guild of Skullduggerous Intent Join Date: Jan 2004 Location: Socal Posts: 7,841 Trader Rating: (48) Feedback Score: 48 reviews	Seen them but they've been custom one of deals. As far as I know, no one mass produces them. I tried talking a buddy that works at a machine shop into making them but he's a pothead and I'm too lazy = fail. Another solution would be to use the SR pump and have the lines spliced by a willing and competent AC shop, then recharge the system. There is one here in Gardena that does it - I know, lot of help that'd do you. Good luck.