Rewiring of Harness - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

live2drift2live · 01-22-2003, 10:28 AM

I have been searching and been seeing a lot of notes of having to solder and rewire your SR harness. Is this tru? or just for cut lines? B/c if it is I was wondering where I can get a diagram so I can possibly make a plug and play system adaptor for the harness once i get my swap. Thanks alot
JBM

Foxcolt · 01-22-2003, 11:36 AM

Buy a car, drive it around. Save some money then email me.

N1ceDrgn · 01-22-2003, 01:26 PM

Check out www.heavythrottle.com , they have a diagram listed there that explains what needs to be connected to what... Also, it is possible to swimply disassemble the wiring connections and change the pin-outs. That's a better method that cutting and splicing.

TegGSR96 · 01-22-2003, 11:11 PM

is it a hard task to rewire it yourself? ive seen diagrams and stuff and it doesnt look too complicated, but ive heard a lot of people who've had many problems arise..
Alex

N1ceDrgn · 01-22-2003, 11:14 PM

It's not that bad.. do some research, figure out what the wires are for on each end of the harnesses you want to connect.. take your time, re-pin each connector that is supposed to connect, or if you're not that maticulous, take your time and splice them together.. just remember.. take your time and be patient, it's not that bad if you do..

fast-datsun · 01-24-2003, 12:07 PM

solider all splices or some where down the road you WILL have electrical problem from loose but-connectors...

01-22-2003, 10:28 AM	#1
live2drift2live Leaky Injector Join Date: Jan 2003 Location: VA Posts: 88 Trader Rating: (0) Feedback Score: 0 reviews	Rewiring of Harness I have been searching and been seeing a lot of notes of having to solder and rewire your SR harness. Is this tru? or just for cut lines? B/c if it is I was wondering where I can get a diagram so I can possibly make a plug and play system adaptor for the harness once i get my swap. Thanks alot JBM __________________ Goals in Life- Get a 240SX- soon Get Turbo-distant Learn Japanese and go to Japan-Far far away in land of rising sun.

01-22-2003, 11:36 AM	#2
Foxcolt Zilvia FREAK! Join Date: Apr 2002 Location: Northern VA Posts: 1,264 Trader Rating: (0) Feedback Score: 0 reviews	Buy a car, drive it around. Save some money then email me. __________________ Driftec www.midatlantic240sx.com

01-22-2003, 01:26 PM	#3
N1ceDrgn Zilvia Member Join Date: Nov 2002 Location: SoCal Posts: 259 Trader Rating: (0) Feedback Score: 0 reviews	Check out www.heavythrottle.com , they have a diagram listed there that explains what needs to be connected to what... Also, it is possible to swimply disassemble the wiring connections and change the pin-outs. That's a better method that cutting and splicing. __________________ ..working on something that is slowly getting built up and restored..

01-22-2003, 11:14 PM	#5
N1ceDrgn Zilvia Member Join Date: Nov 2002 Location: SoCal Posts: 259 Trader Rating: (0) Feedback Score: 0 reviews	It's not that bad.. do some research, figure out what the wires are for on each end of the harnesses you want to connect.. take your time, re-pin each connector that is supposed to connect, or if you're not that maticulous, take your time and splice them together.. just remember.. take your time and be patient, it's not that bad if you do.. __________________ ..working on something that is slowly getting built up and restored..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-22-2003, 11:11 PM	#4
TegGSR96 Join Date: Jan 2003 Location: Ottawa, Ont Posts: 12 Trader Rating: (0) Feedback Score: 0 reviews	is it a hard task to rewire it yourself? ive seen diagrams and stuff and it doesnt look too complicated, but ive heard a lot of people who've had many problems arise.. Alex

01-24-2003, 12:07 PM	#6
fast-datsun Leaky Injector Join Date: Aug 2002 Posts: 116 Trader Rating: (0) Feedback Score: 0 reviews	solider all splices or some where down the road you WILL have electrical problem from loose but-connectors...