Ls2 s13 hatch need opinions - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

mikulec240 · 06-04-2010, 08:56 AM

do you guys think i will need a whole new rear end to it or with the s13 one hold up?
upgrading full brembos and gonna need full suspension anyone have any ideas?
still looking for an s14 shell if anyone has a clean one

g6civcx · 06-04-2010, 09:12 AM

Durability will be fine, but the 4.083 may be too much gear.

mikulec240 · 06-04-2010, 09:26 AM

well i can get a gto rear end with the engine.. jsut dont know if it will fit on there
because it is gonan be a lot of power

g6civcx · 06-04-2010, 09:57 AM

Look at the subframe. Look at the GTO diff. See what you think.

Until you break 700-800 ft-lbs on big slicks, the diff will hold up. The axles/driveshafts will break before the diff will.

lazysk8er2 · 06-06-2010, 12:25 AM

ak_slick · 06-06-2010, 12:29 AM

R200 will be fine. Axles might break. There is any easy replacement with a z32tt axle and a q45 axle that has been used up to around 700-800 ft-lbs with no problems. Check on ka-t.

If you need to swap ring and pinion of the r200 there are TONS of options. All the way down to a 3.53 iirc.

Slammed Assassin · 06-06-2010, 12:30 AM

welded diffs will hold. id just get beefy axles.

g6civcx · 06-06-2010, 12:47 AM

Quote:

Originally Posted by ak_slick

If you need to swap ring and pinion of the r200 there are TONS of options. All the way down to a 3.53 iirc.

3.133 is as low as you can go without custom.

06-04-2010, 08:56 AM	#1
mikulec240 Leaky Injector Join Date: Oct 2008 Location: crystal lake Age: 36 Posts: 54 Trader Rating: (0) Feedback Score: 0 reviews	Ls2 s13 hatch need opinions do you guys think i will need a whole new rear end to it or with the s13 one hold up? upgrading full brembos and gonna need full suspension anyone have any ideas? still looking for an s14 shell if anyone has a clean one

06-06-2010, 12:30 AM	#7
Slammed Assassin Nissanaholic! Join Date: Feb 2007 Location: Oxnard/SV Posts: 2,065 Trader Rating: (34) Feedback Score: 34 reviews	welded diffs will hold. id just get beefy axles. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

06-04-2010, 09:12 AM	#2
g6civcx Post Whore! Join Date: Apr 2004 Location: Virginia, USA Posts: 5,764 Trader Rating: (5) Feedback Score: 5 reviews	Durability will be fine, but the 4.083 may be too much gear.

06-04-2010, 09:26 AM	#3
mikulec240 Leaky Injector Join Date: Oct 2008 Location: crystal lake Age: 36 Posts: 54 Trader Rating: (0) Feedback Score: 0 reviews	well i can get a gto rear end with the engine.. jsut dont know if it will fit on there because it is gonan be a lot of power

06-04-2010, 09:57 AM	#4
g6civcx Post Whore! Join Date: Apr 2004 Location: Virginia, USA Posts: 5,764 Trader Rating: (5) Feedback Score: 5 reviews	Look at the subframe. Look at the GTO diff. See what you think. Until you break 700-800 ft-lbs on big slicks, the diff will hold up. The axles/driveshafts will break before the diff will.

06-06-2010, 12:29 AM	#6
ak_slick Leaky Injector Join Date: Dec 2006 Location: Las Vegas Posts: 78 Trader Rating: (0) Feedback Score: 0 reviews	R200 will be fine. Axles might break. There is any easy replacement with a z32tt axle and a q45 axle that has been used up to around 700-800 ft-lbs with no problems. Check on ka-t. If you need to swap ring and pinion of the r200 there are TONS of options. All the way down to a 3.53 iirc.