PA RB26DETT R32 Motor in parts - trade for other motorset - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

OutToWinPAHC · 09-01-2013, 03:51 PM

I got this motor as part of a large trade then tried to trade if for a running RB25DET or RB20DET swap and since have decided to just buy a motor. So I have edited this to a for sale thread. Located in Philadlephia PA. Will take 1300 for everything, I am not parting it out... yet anyhow I rather sell it as the lot..

R32 RB26DETT

Bare Block with crank girdle and rear main cover $450
Stock Crank, good clean journals $350
Stock cams $ Sold
OEM pistons with connecting rods $120
Timing components -will go with block
oil pickup goes - with block
GTR oil pan wit diff (no axles or axle seals ) $100
Cylinder head - should be taken apart, cleaned, and new valve stem seals and solid lifters should be reshimmed. I only have about 20 or the 24 OEM shims, but you should be re-shimming anyhow if your building up. $350.00
ECUs $150 for the early R32, $170 for the later R32
Engine harness, coil harness, ignitor, injector harness $ Sold
power steering pump (Hicas ) $40.00
Power steer pump bracket RB26 $40.00
OEM turbo piping, tubes, BOV, suction parts $50.00 for the lot add $20 for the BOV's
MAFs both for $75
CAS $45
Intake and ITB's and IAC valve (no coolant temp sensors or TPS) $175.00

Ask me about any small parts -

Block needs a hone or boring, though there is still some cross hatch. Requires ARP main studs (old owner did not label main bolts in order, and cylinder head should be serviced with shimming (you should be doing this anyhow). I dont have the coil packs,

Jdmsilivias13 · 09-01-2013, 04:49 PM

Text me ASAP 484.238.6345

OutToWinPAHC · 09-02-2013, 11:15 AM

Available as motor, motor without cams, or everything including trans minus rear shaft. Will also consider a RB20DET swap

BB4rank · 09-02-2013, 12:48 PM

were are you located?

OutToWinPAHC · 09-02-2013, 03:36 PM

Philadelphia PA

OutToWinPAHC · 09-03-2013, 09:10 PM

Edited ad to a for sale ad. 1300 for all of it will go 1100 without trans, shafts, or OEM cams

RB25GUY · 09-04-2013, 07:47 PM

willing to sell the itbs and plenum?

Slide13 · 09-04-2013, 08:36 PM

Still got this? I have 2 rb20's ones fresh out the machine shop.... hmu

OutToWinPAHC · 09-05-2013, 04:40 AM

I got a local offer on the head and ITB's but what is your offer for the ITB's and intake. There is no sensors

funktown240 · 09-05-2013, 05:37 PM

How much for the crank?

OutToWinPAHC · 09-05-2013, 07:28 PM

350 journals are all good and clean

funktown240 · 09-05-2013, 07:55 PM

PM sent!!!

09-01-2013, 03:51 PM	#1
OutToWinPAHC Zilvia Addict Join Date: May 2007 Location: Florida Posts: 746 Trader Rating: (6) Feedback Score: 6 reviews	RB26DETT R32 Motor in parts - trade for other motorset I got this motor as part of a large trade then tried to trade if for a running RB25DET or RB20DET swap and since have decided to just buy a motor. So I have edited this to a for sale thread. Located in Philadlephia PA. Will take 1300 for everything, I am not parting it out... yet anyhow I rather sell it as the lot.. R32 RB26DETT Bare Block with crank girdle and rear main cover $450 Stock Crank, good clean journals $350 Stock cams $ Sold OEM pistons with connecting rods $120 Timing components -will go with block oil pickup goes - with block GTR oil pan wit diff (no axles or axle seals ) $100 Cylinder head - should be taken apart, cleaned, and new valve stem seals and solid lifters should be reshimmed. I only have about 20 or the 24 OEM shims, but you should be re-shimming anyhow if your building up. $350.00 ECUs $150 for the early R32, $170 for the later R32 Engine harness, coil harness, ignitor, injector harness $ Sold power steering pump (Hicas ) $40.00 Power steer pump bracket RB26 $40.00 OEM turbo piping, tubes, BOV, suction parts $50.00 for the lot add $20 for the BOV's MAFs both for $75 CAS $45 Intake and ITB's and IAC valve (no coolant temp sensors or TPS) $175.00 Ask me about any small parts - Block needs a hone or boring, though there is still some cross hatch. Requires ARP main studs (old owner did not label main bolts in order, and cylinder head should be serviced with shimming (you should be doing this anyhow). I dont have the coil packs, Last edited by OutToWinPAHC; 09-07-2013 at 06:17 PM..

09-02-2013, 12:48 PM	#4
BB4rank Leaky Injector Join Date: Jun 2011 Location: United States Posts: 122 Trader Rating: (9) Feedback Score: 9 reviews	were are you located? __________________ So you guys every eat cheese? Cheese is a funny thing...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-01-2013, 04:49 PM	#2
Jdmsilivias13 Leaky Injector Join Date: Jan 2013 Location: West Chester pa Age: 37 Posts: 68 Trader Rating: (2) Feedback Score: 2 reviews	Text me ASAP 484.238.6345

09-02-2013, 11:15 AM	#3
OutToWinPAHC Zilvia Addict Join Date: May 2007 Location: Florida Posts: 746 Trader Rating: (6) Feedback Score: 6 reviews	Available as motor, motor without cams, or everything including trans minus rear shaft. Will also consider a RB20DET swap

09-02-2013, 03:36 PM	#5
OutToWinPAHC Zilvia Addict Join Date: May 2007 Location: Florida Posts: 746 Trader Rating: (6) Feedback Score: 6 reviews	Philadelphia PA

09-03-2013, 09:10 PM	#6
OutToWinPAHC Zilvia Addict Join Date: May 2007 Location: Florida Posts: 746 Trader Rating: (6) Feedback Score: 6 reviews	Edited ad to a for sale ad. 1300 for all of it will go 1100 without trans, shafts, or OEM cams

09-04-2013, 07:47 PM	#7
RB25GUY Nissanaholic! Join Date: Feb 2013 Location: NY Age: 35 Posts: 2,033 Trader Rating: (9) Feedback Score: 9 reviews	willing to sell the itbs and plenum?

09-04-2013, 08:36 PM	#8
Slide13 Join Date: Jul 2008 Location: Indiana Age: 36 Posts: 13 Trader Rating: (0) Feedback Score: 0 reviews	Still got this? I have 2 rb20's ones fresh out the machine shop.... hmu

09-05-2013, 04:40 AM	#9
OutToWinPAHC Zilvia Addict Join Date: May 2007 Location: Florida Posts: 746 Trader Rating: (6) Feedback Score: 6 reviews	I got a local offer on the head and ITB's but what is your offer for the ITB's and intake. There is no sensors

09-05-2013, 05:37 PM	#10
funktown240 Zilvia Member Join Date: Mar 2012 Location: Ft. Worth Age: 41 Posts: 258 Trader Rating: (10) Feedback Score: 10 reviews	How much for the crank?

09-05-2013, 07:28 PM	#11
OutToWinPAHC Zilvia Addict Join Date: May 2007 Location: Florida Posts: 746 Trader Rating: (6) Feedback Score: 6 reviews	350 journals are all good and clean

09-05-2013, 07:55 PM	#12
funktown240 Zilvia Member Join Date: Mar 2012 Location: Ft. Worth Age: 41 Posts: 258 Trader Rating: (10) Feedback Score: 10 reviews	PM sent!!!