Xcessive SR20 to VG Transmission Adapter - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

alesserfate · 01-20-2009, 04:09 PM

Holler,

I've searched but haven't found exactly what I need so here goes:

I'm looking to upgrade from stock SR tranny on my drift car to Z32 tranny for obvious reasons. Now, I know quite a few people who run the mazworx kit. Has anybody out there tried this kit ?

Xcessive SR20 to VG Transmission Adapter Xcessive Manufacturing

Any opinions on Xcessive and/or this kit ?

jim1234664 · 01-20-2009, 07:55 PM

never heard of it, but thats not saying much

Monooxide · 01-20-2009, 09:01 PM

At one point I had a KA24DE manifold and Top Mount Mani from them, but EXCELLENT quality parts.

Charlie · 01-20-2009, 09:16 PM

Link doesn't work

***S14DB*** · 01-20-2009, 09:18 PM

Does this space the input shaft out of the crank?

Howlermonkey · 01-21-2009, 07:00 AM

Austin Hoke of the hybridz pages makes one to adapt the z32 tranny to a L series engine so it might not be much to convince him to consider what you need.

Z32 Install Version 2. - HybridZ

smelly240 · 01-21-2009, 07:26 AM

Quote:

Originally Posted by S14DB

Does this space the input shaft out of the crank?

The input shaft will only go into the flywheel's hole from the look of it - that spacer is there tho to move the flywheel out (i assume the spacer will replace the crank to hold the pilot???)

turbo2nr · 01-21-2009, 07:38 AM

alot of the ka-t guys run it when making over 500whp. seems to be good try searching on ka-t.org im sure you'll find something.

yes i know you are goging to use it for a sr..

***S14DB*** · 01-21-2009, 02:01 PM

Quote:

Originally Posted by smelly240

The input shaft will only go into the flywheel's hole from the look of it - that spacer is there tho to move the flywheel out (i assume the spacer will replace the crank to hold the pilot???)

Quote:

Install the flywheel spacer and flywheel with the new 12mm bolts. Some crankshafts have an additional pilot sleeve that will interfere with the new spacer. These are typical on crankshafts that came from automatic transmissions. You will need to remove or grind this sleeve to accommodate the flywheel spacer. Use the 6 supplied 12mm washers with the new flywheel bolts. Be sure to check that the bolts do not bottom out, if they bottom out you will need to grind the bolts to allow proper seating. Use thread locker on the flywheel bolts and torque to factory specs. Hold the clutch disc on the flywheel using a clutch pilot tool and check the springs in the hub for clearance to the new flywheel bolts by rotating the clutch 360 degrees while holding it tight to the flywheel. If contact exists, clearance the bolt heads as needed.

The flywheel spacer comes with a new pilot bushing installed. The clutch can now be reinstalled. Follow factory or clutch manufacturer specs for clutch installation.

I hope that that spacer taps into the crank and not centers on the flywheel bolts. Then there is a ring on the crank to center the flywheel. Whole think looks like a clutch or flywheel launch scenario. But I won't pass judgment till I see the install of this kit.

alesserfate · 01-22-2009, 01:53 AM

Quote:

Originally Posted by S14DB

I hope that that spacer taps into the crank and not centers on the flywheel bolts. Then there is a ring on the crank to center the flywheel. Whole think looks like a clutch or flywheel launch scenario. But I won't pass judgment till I see the install of this kit.

That is, precisely, why I made this thread. I don't wanna lose my ankles.

***S14DB*** · 01-22-2009, 06:26 AM

Quote:

Originally Posted by alesserfate

That is, precisely, why I made this thread. I don't wanna lose my ankles.

yeah, I know a guy with some flexplate in his leg. Those 12mm "washers" scare the hell out of me.

smelly240 · 01-22-2009, 06:32 AM

I agree - but if its got a weiner than goes into the crank it might be ok.

Brian W. · 01-22-2009, 12:21 PM

i dont like the spacing the flywheel out idea.

Id stick with my mazworx over that one.

SuperiorS14 · 02-06-2009, 06:30 PM

my buddy is using that kit on his drag s13.....

P2M/G-DIMENSION S13 Drag Coupe

1989rps13 · 02-06-2009, 07:02 PM

That looks like a sweet setup

2000gtx · 02-07-2009, 04:29 PM

we use the mazworx set up in our drag 510 with sr20det and so far has worked flawlessly..the fit is good...we are currently installing one in a s13 for drag use also...

*kognition* · 06-08-2009, 04:15 PM

Any updates on this? Did you buy the kit?

Slidin' Sam · 10-16-2010, 11:30 AM

Has anybody used this kit? I have been searching for the past two hours (and it's not the first time i have looked either) trying to gather information on this kit/other z32 transmission swaps and haven't found much of anything, except for "What do you guy's think of this?". Thanks!

!Zar! · 10-16-2010, 02:19 PM

That site doesn't know the difference between your and you're.

Reason enough not to buy.

alesserfate · 12-18-2011, 03:05 PM

I ended up not buying it, simply because I don't know how well that flywheel spacer will last with aggressive clutch and prolonged street abuse.

surfpac · 12-21-2011, 08:47 AM

Look for a Mazworx setup. I just purchased one including Z32 tranny from a Zilvia member who was parting his car out. Look out for used ones on here, or save up for brand new from Mazworx. Those guys are knowledgeable and have experience.

Slidin' Sam · 12-22-2011, 11:49 AM

I bought the mazworx kit and it works great! I too was concerned with the flywheel spacer so I went with this kit instead. Everything bolted up fine...some stuff required a little fab/extra love, but it all works smooth. z32 trans on a sr is the way it was meant to be! lol

supersayianjim · 03-09-2019, 06:13 PM

Old as fuck thead, but tell me about this mazoworks kit?

*brndck* · 03-11-2019, 07:48 AM

Quote:

Originally Posted by supersayianjim

Old as fuck thead, but tell me about this mazoworks kit?

you've been here wayyyyyyy too long for this

http://lmgtfy.com/?q=mazworx

01-20-2009, 04:09 PM	#1
alesserfate Zilvia Member Join Date: Oct 2007 Location: Ontario Posts: 180 Trader Rating: (2) Feedback Score: 2 reviews	Xcessive SR20 to VG Transmission Adapter Holler, I've searched but haven't found exactly what I need so here goes: I'm looking to upgrade from stock SR tranny on my drift car to Z32 tranny for obvious reasons. Now, I know quite a few people who run the mazworx kit. Has anybody out there tried this kit ? Xcessive SR20 to VG Transmission Adapter Xcessive Manufacturing Any opinions on Xcessive and/or this kit ? __________________

01-20-2009, 09:16 PM	#4
Charlie Zilvia Addict Join Date: Oct 2007 Location: SoCal (626) Posts: 667 Trader Rating: (35) Feedback Score: 35 reviews	Link doesn't work __________________

01-20-2009, 09:18 PM	#5
*S14DB* AFC #1 Join Date: Oct 2003 Location: 昨晩あなたのお母さんの家 Posts: 20,181 Trader Rating: (3) Feedback Score: 3 reviews	Does this space the input shaft out of the crank? __________________ Comments should be taken as Opinions not as Statements of Fact

01-21-2009, 07:38 AM	#8
turbo2nr Post Whore! Join Date: Jan 2005 Location: queens NYC Age: 39 Posts: 2,561 Trader Rating: (8) Feedback Score: 8 reviews	alot of the ka-t guys run it when making over 500whp. seems to be good try searching on ka-t.org im sure you'll find something. yes i know you are goging to use it for a sr.. __________________ s14 kouki ka-t

01-22-2009, 06:32 AM	#12
smelly240 Nissanaholic! Join Date: Oct 2006 Location: Philaburbia Age: 47 Posts: 2,137 Trader Rating: (4) Feedback Score: 4 reviews	I agree - but if its got a weiner than goes into the crank it might be ok. __________________ HREs on a S13 - check, 6262 - check, Girlfriend.... - nope

01-20-2009, 07:55 PM	#2
jim1234664 Zilvia Member Join Date: Nov 2004 Location: Buffalo, NY Posts: 227 Trader Rating: (1) Feedback Score: 1 reviews	never heard of it, but thats not saying much

01-20-2009, 09:01 PM	#3
Monooxide Zilvia Addict Join Date: Mar 2005 Location: Farmington/Flint, MI Age: 37 Posts: 675 Trader Rating: (8) Feedback Score: 8 reviews	At one point I had a KA24DE manifold and Top Mount Mani from them, but EXCELLENT quality parts.

01-21-2009, 07:00 AM	#6
Howlermonkey Leaky Injector Join Date: Jan 2009 Location: west palm Posts: 107 Trader Rating: (0) Feedback Score: 0 reviews	Austin Hoke of the hybridz pages makes one to adapt the z32 tranny to a L series engine so it might not be much to convince him to consider what you need. Z32 Install Version 2. - HybridZ

01-22-2009, 12:21 PM	#13
Brian W. Zilvia.net Advertiser Join Date: Feb 2004 Location: Baltimore, MD Age: 41 Posts: 1,146 Trader Rating: (8) Feedback Score: 8 reviews	i dont like the spacing the flywheel out idea. Id stick with my mazworx over that one. __________________ www.ma-motorsports.com -Fab work, builds, swaps, dyno tuning

02-06-2009, 06:30 PM	#14
SuperiorS14 Zilvia FREAK! Join Date: Feb 2007 Location: S.G.V. Age: 40 Posts: 1,138 Trader Rating: (20) Feedback Score: 20 reviews	my buddy is using that kit on his drag s13..... P2M/G-DIMENSION S13 Drag Coupe

02-06-2009, 07:02 PM	#15
1989rps13 BANNED Join Date: Sep 2007 Location: socal Posts: 1,499 Trader Rating: (10) Feedback Score: 10 reviews	That looks like a sweet setup

02-07-2009, 04:29 PM	#16
2000gtx Leaky Injector Join Date: Feb 2009 Location: socal Posts: 66 Trader Rating: (2) Feedback Score: 2 reviews	we use the mazworx set up in our drag 510 with sr20det and so far has worked flawlessly..the fit is good...we are currently installing one in a s13 for drag use also...

06-08-2009, 04:15 PM	#17
kognition Premium Member Join Date: May 2004 Location: Santee California Posts: 2,107 Trader Rating: (6) Feedback Score: 6 reviews	Any updates on this? Did you buy the kit?

10-16-2010, 11:30 AM	#18
Slidin' Sam Zilvia Addict Join Date: Jul 2009 Location: Japan Posts: 729 Trader Rating: (9) Feedback Score: 9 reviews	Has anybody used this kit? I have been searching for the past two hours (and it's not the first time i have looked either) trying to gather information on this kit/other z32 transmission swaps and haven't found much of anything, except for "What do you guy's think of this?". Thanks! __________________

10-16-2010, 02:19 PM	#19
!Zar! Post Whore! Join Date: Nov 2004 Location: North Korea Posts: 14,579 Trader Rating: (27) Feedback Score: 27 reviews	That site doesn't know the difference between your and you're. Reason enough not to buy. __________________

12-18-2011, 03:05 PM	#20
alesserfate Zilvia Member Join Date: Oct 2007 Location: Ontario Posts: 180 Trader Rating: (2) Feedback Score: 2 reviews	I ended up not buying it, simply because I don't know how well that flywheel spacer will last with aggressive clutch and prolonged street abuse. __________________

12-21-2011, 08:47 AM	#21
surfpac Zilvia Member Join Date: Nov 2001 Location: Fort Lauderdale, FL Posts: 155 Trader Rating: (1) Feedback Score: 1 reviews	Look for a Mazworx setup. I just purchased one including Z32 tranny from a Zilvia member who was parting his car out. Look out for used ones on here, or save up for brand new from Mazworx. Those guys are knowledgeable and have experience.

12-22-2011, 11:49 AM	#22
Slidin' Sam Zilvia Addict Join Date: Jul 2009 Location: Japan Posts: 729 Trader Rating: (9) Feedback Score: 9 reviews	I bought the mazworx kit and it works great! I too was concerned with the flywheel spacer so I went with this kit instead. Everything bolted up fine...some stuff required a little fab/extra love, but it all works smooth. z32 trans on a sr is the way it was meant to be! lol __________________

03-09-2019, 06:13 PM	#23
supersayianjim Nissanaholic! Join Date: Jan 2010 Location: location X Posts: 1,815 Trader Rating: (10) Feedback Score: 10 reviews	Old as fuck thead, but tell me about this mazoworks kit? __________________ http://www.240sxforums.com/forums/rb...ject-s-rb.html