s14 tranny in sohc driveshaft help help help - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

thinkjdm · 02-11-2006, 01:44 PM

will the 95 ka manual tranny fit on the sohc manual driveshaft? help help help!!

projectRDM · 02-11-2006, 04:38 PM

Do we really need to answer this question every day?

It's the SAME FUCKING transmission.

thinkjdm · 02-11-2006, 11:17 PM

need to know asap...do i need to switch to s14 driveshaft?

dct223 · 02-11-2006, 11:27 PM

read what russ just said above.......

only difference is like a damn hole on the bell housing

thinkjdm · 02-12-2006, 01:33 AM

what can cause the driveshaft not to slide inside the tranny?

dct223 · 02-12-2006, 01:52 AM

not aligning it right, not turning the driveshaft... try unbolting the front 1/2 shaft and turning it like that, much easier

ryan hagen · 02-12-2006, 10:21 AM

actually to do the swap right you need to take the large black metal/rubber tailshaft seal guard/shroud off and replace it with a metal smaller one that the s13 had, the dirve shafts are differnt, the s14 wont interchange, but a s13 drive shaft with a vibration damper wont fit on the s14 tranney with the shroud on. i swapped a s13 tail shaft housing on because the metal s13 piece is mostlikly expensive or unavailable.

if that shroud is still on it wont even come close to fitting.

and auto drive shafts dont work either.

02-11-2006, 01:44 PM	#1
thinkjdm Join Date: Sep 2005 Location: 41510 Posts: 28 Trader Rating: (0) Feedback Score: 0 reviews	s14 tranny in sohc driveshaft help help help will the 95 ka manual tranny fit on the sohc manual driveshaft? help help help!!

02-11-2006, 04:38 PM	#2
projectRDM Post Whore! Join Date: Dec 2002 Location: Atlanta Age: 51 Posts: 13,812 Trader Rating: (12) Feedback Score: 12 reviews	Do we really need to answer this question every day? It's the SAME FUCKING transmission. __________________ FORMERLY R240NA Learn what's really going on and protect your assets now before they're gone forever: www.paypalsucks.com

02-11-2006, 11:27 PM	#4
dct223 Nissanaholic! Join Date: Nov 2003 Location: hella NORCAL! Age: 39 Posts: 1,664 Trader Rating: (4) Feedback Score: 4 reviews	read what russ just said above....... only difference is like a damn hole on the bell housing __________________ Sfourteen

02-12-2006, 01:52 AM	#6
dct223 Nissanaholic! Join Date: Nov 2003 Location: hella NORCAL! Age: 39 Posts: 1,664 Trader Rating: (4) Feedback Score: 4 reviews	not aligning it right, not turning the driveshaft... try unbolting the front 1/2 shaft and turning it like that, much easier __________________ Sfourteen

02-12-2006, 10:21 AM	#7
ryan hagen Zilvia FREAK! Join Date: Jan 2003 Location: rhinelander wisconsin Age: 42 Posts: 1,465 Trader Rating: (8) Feedback Score: 8 reviews	actually to do the swap right you need to take the large black metal/rubber tailshaft seal guard/shroud off and replace it with a metal smaller one that the s13 had, the dirve shafts are differnt, the s14 wont interchange, but a s13 drive shaft with a vibration damper wont fit on the s14 tranney with the shroud on. i swapped a s13 tail shaft housing on because the metal s13 piece is mostlikly expensive or unavailable. if that shroud is still on it wont even come close to fitting. and auto drive shafts dont work either. __________________ 1990 hatch ka24de gt2871r

02-11-2006, 11:17 PM	#3
thinkjdm Join Date: Sep 2005 Location: 41510 Posts: 28 Trader Rating: (0) Feedback Score: 0 reviews	need to know asap...do i need to switch to s14 driveshaft?

02-12-2006, 01:33 AM	#5
thinkjdm Join Date: Sep 2005 Location: 41510 Posts: 28 Trader Rating: (0) Feedback Score: 0 reviews	what can cause the driveshaft not to slide inside the tranny?