MD SERIOUS SR20DET STROKER MOTOR for sale... - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Brian W. · 03-11-2009, 11:30 AM

Ok, We are selling this Motor.. It will be practically brand new. Its an s13 SR20DET and it will be sold as a complete long block from valve cover to oil pan.

This is the motor out of JR's S14 that did not last very long(story here: DRIVERS>>VAUGHN GITTIN JR BLOG ENTRY#3 - Speedhunters)

Specs are as follows:

MA-Motorsports built 2.2 Liter S13 SR20DET long block:
-JE 9:1 Custom stroker pistons
-Bored 20 over
-Brian Crower Billet Stroker Crank
-Brian Crower 625+ Stroker Con rods
-chamfered oil passages in block
-ACL Race Rod Bearings
-ACL Race Main bearings
-ARP GTIR Oversized head studs
-Drilled head and block for oversized head studs
-Apexi Head Gasket (cut for oversized studs)
-Open combustion chambers, polished
-Radius valve job
-Solid Lash Adjusters (with initial setup)(or hydro LAs)
-Brian Crower stainless Valves
-Brian Crower Ti retainers and valve springs
-Brian Crower Stage 2 camshafts
-JUN Cam gears
-Custom Blue paint valve cover with DA/ American flag logo vinyl
-Greddy Oil Pan
-S14 SR Water Pump
-Signal Carbon coilpack cover with the vinyl over it.
-A couple accessories will also be included: alt. w/ powdercoated brackets, PS pump w/ powdercoated brackets

This engine is at the machine shop right now getting fresh bearings put in and all tolerances checked, straightened, etc. and everything will be cleaned and like new. When i get it back from them i will personally assemble it as a complete long block and can ship right away.

This is pretty much the same motor i run in my car.... It RIPS! I can advise on various turbo setups to run with this engine to meet your power goals.

Serious inquires please email me.

$6000.00 OBO If you are serious, and want a real deal motor and have some money... shoot an offer.

Brian W. · 03-11-2009, 11:41 PM

will also of course have all new gaskets and seals installed.

Ceepo · 03-12-2009, 11:06 AM

Sad what happened to that car

but that is definatly a sick motor!!! GLWS

simplistek · 03-12-2009, 11:17 AM

damn... i wish i had $6k.

slider2828 · 03-12-2009, 11:30 AM

It said in the story read it.... JR let his dad drive his car after the initial test session... JR's dad got squirely lost it and head first into wall then tail.... Read lol

jr_ss · 03-12-2009, 03:16 PM

Quote:

Originally Posted by Ceepo

Sad what happened to that car

but that is definatly a sick motor!!! GLWS

Quote:

Originally Posted by slider2828

It said in the story read it.... JR let his dad drive his car after the initial test session... JR's dad got squirely lost it and head first into wall then tail.... Read lol

You fail at reading... He was saying it was sad at what happened to JR's car. Not asking what happened to it.

Anyways, this is a sick motor. I wish I hadn't just finished building mine.

bewst pewp · 03-12-2009, 12:07 PM

good deal...

stokers for sr are crazy expensive

*wangan_cruiser* · 03-12-2009, 12:18 PM

sick car but you can always build another car. but you cant have another dad just like that.

sick motor and car. glad your dad came out fine. even with 3 broken ribs at least he wasnt in critical condition.

adam bergener · 03-12-2009, 12:34 PM

that's a gnarly motor..

slider2828 · 03-12-2009, 12:49 PM

Mike is the builder, JR Vaughn Gitten's Dad is in reference ahahha...

CIutchCollidE · 03-12-2009, 03:58 PM

thats a sick motor. glws

Brian W. · 03-15-2009, 07:44 PM

Hey thanks guys, this is a gnarly motor for sure. I run the same one but will be using an SR20VE cyl head this year. The motor makes pretty good torque with the right turbo srtup on it.

Please keep this in mind and feel free to ask any questions.

03-11-2009, 11:30 AM	#1
Brian W. Zilvia.net Advertiser Join Date: Feb 2004 Location: Baltimore, MD Age: 41 Posts: 1,146 Trader Rating: (8) Feedback Score: 8 reviews	SERIOUS SR20DET STROKER MOTOR for sale... Ok, We are selling this Motor.. It will be practically brand new. Its an s13 SR20DET and it will be sold as a complete long block from valve cover to oil pan. This is the motor out of JR's S14 that did not last very long(story here: DRIVERS>>VAUGHN GITTIN JR BLOG ENTRY#3 - Speedhunters) Specs are as follows: MA-Motorsports built 2.2 Liter S13 SR20DET long block: -JE 9:1 Custom stroker pistons -Bored 20 over -Brian Crower Billet Stroker Crank -Brian Crower 625+ Stroker Con rods -chamfered oil passages in block -ACL Race Rod Bearings -ACL Race Main bearings -ARP GTIR Oversized head studs -Drilled head and block for oversized head studs -Apexi Head Gasket (cut for oversized studs) -Open combustion chambers, polished -Radius valve job -Solid Lash Adjusters (with initial setup)(or hydro LAs) -Brian Crower stainless Valves -Brian Crower Ti retainers and valve springs -Brian Crower Stage 2 camshafts -JUN Cam gears -Custom Blue paint valve cover with DA/ American flag logo vinyl -Greddy Oil Pan -S14 SR Water Pump -Signal Carbon coilpack cover with the vinyl over it. -A couple accessories will also be included: alt. w/ powdercoated brackets, PS pump w/ powdercoated brackets This engine is at the machine shop right now getting fresh bearings put in and all tolerances checked, straightened, etc. and everything will be cleaned and like new. When i get it back from them i will personally assemble it as a complete long block and can ship right away. This is pretty much the same motor i run in my car.... It RIPS! I can advise on various turbo setups to run with this engine to meet your power goals. Serious inquires please email me. $6000.00 OBO If you are serious, and want a real deal motor and have some money... shoot an offer. __________________ www.ma-motorsports.com -Fab work, builds, swaps, dyno tuning

03-11-2009, 11:41 PM	#2
Brian W. Zilvia.net Advertiser Join Date: Feb 2004 Location: Baltimore, MD Age: 41 Posts: 1,146 Trader Rating: (8) Feedback Score: 8 reviews	will also of course have all new gaskets and seals installed. __________________ www.ma-motorsports.com -Fab work, builds, swaps, dyno tuning

03-12-2009, 11:17 AM	#4
simplistek Zilvia Junkie Join Date: Mar 2007 Location: San Diego Posts: 463 Trader Rating: (7) Feedback Score: 7 reviews	damn... i wish i had $6k. __________________ v e r t e x - u s a . c o m

03-12-2009, 11:30 AM	#5
slider2828 Post Whore! Join Date: Oct 2004 Location: San Francisco, CA Posts: 6,040 Trader Rating: (13) Feedback Score: 13 reviews	It said in the story read it.... JR let his dad drive his car after the initial test session... JR's dad got squirely lost it and head first into wall then tail.... Read lol __________________ Turn and Burn!

03-12-2009, 12:49 PM	#10
slider2828 Post Whore! Join Date: Oct 2004 Location: San Francisco, CA Posts: 6,040 Trader Rating: (13) Feedback Score: 13 reviews	Mike is the builder, JR Vaughn Gitten's Dad is in reference ahahha... __________________ Turn and Burn!

03-12-2009, 11:06 AM	#3
Ceepo Nissanaholic! Join Date: Jan 2008 Location: Cedar City, Utah Posts: 2,007 Trader Rating: (9) Rides Gallery: Ceepo Feedback Score: 9 reviews	Sad what happened to that car but that is definatly a sick motor!!! GLWS __________________ TW: http://zilvia.net/f/cars-sale/390459...d9s-coils.html

03-12-2009, 12:07 PM	#7
bewst pewp Join Date: Feb 2009 Location: ga Age: 37 Posts: 41 Trader Rating: (0) Feedback Score: 0 reviews	good deal... stokers for sr are crazy expensive

03-12-2009, 12:18 PM	#8
wangan_cruiser kouki man Join Date: Apr 2006 Location: downtown oakland,ca Age: 40 Posts: 3,539 Trader Rating: (36) Feedback Score: 36 reviews	sick car but you can always build another car. but you cant have another dad just like that. sick motor and car. glad your dad came out fine. even with 3 broken ribs at least he wasnt in critical condition.

03-12-2009, 12:34 PM	#9
adam bergener Join Date: Jun 2008 Location: massillon ohio Age: 36 Posts: 33 Trader Rating: (0) Feedback Score: 0 reviews	that's a gnarly motor..

03-12-2009, 03:58 PM	#11
CIutchCollidE Zilvia Junkie Join Date: Sep 2008 Location: Cali Posts: 373 Trader Rating: (1) Feedback Score: 1 reviews	thats a sick motor. glws

03-15-2009, 07:44 PM	#12
Brian W. Zilvia.net Advertiser Join Date: Feb 2004 Location: Baltimore, MD Age: 41 Posts: 1,146 Trader Rating: (8) Feedback Score: 8 reviews	Hey thanks guys, this is a gnarly motor for sure. I run the same one but will be using an SR20VE cyl head this year. The motor makes pretty good torque with the right turbo srtup on it. Please keep this in mind and feel free to ask any questions. __________________ www.ma-motorsports.com -Fab work, builds, swaps, dyno tuning