PA PBM Spacers-SR CAS-SR Tensioner-Intake manifold-TONS MORE! PLUS 350z-wrx-200sx Parts

[Imarvin240]

- If you low ball me, I won't even respond to you...simple as that.
- Please bump the thread when you view it, thank you.

Invert Mini
- Works perfect, I just don't play anymore
- $175 shipped.


PBM Spacer Packs 4-lug (each pack has a set...I have two packs, so enough for all four wheels) I WILL NOT PART OUT THE SETS!
- BNIB (Brand New In Box)
- $150 Per Pack $275 for both (I had to wait 3 months to get these from PBM)


Axxis S13 Ceramic Front Brake Pads
- BNIB
- $40


S14 Zenki Gauge Cluster
- 87xxx miles
- Perfect Shape
- $70


S14 A/C Bezel
- All tabs are broken
- $15


SR Timing Chain Tensioner
- ~3k miles
- Perfect Shape
- $30


Cam Angle Sensor
- ~3k Miles (purchased NEW)
- PERFECT SHAPE!
- $130 (retails over $350)


Cam Angle Sensor Gasket and O-ring
- Perfect Shape
- $10


Intake and Exhaust Cam Gear Bolts
- PERFECT SHAPE!
- $5 each


SR20 Head Bolts
- Used
- $20


KU Engineering S13 Intake Manifold
- Never Used (just sitting around for about 3yrs, but the last owner drilled injector port 1 larger to put larger injectors in but then sold it to me...costs about 60 to do it to the other 3 or 40 to correct port 1)
- $130


SR20 Upper Oil Pan - SOLD!
SR20 Oil Pump - SOLD!
SR20 Oil Screens (2 sets)
SR20 Rear Crank Case Cover (3)
SR20 Oil Block Galley w/ Sensor (2)


Unknown Brand BOV
- Slightly Used
- PERFECT SHAPE
- $50

SR Main Cap Girdle
- PERFECT SHAPE
- $25 each


SR Coolant Tubes - $20
SR Temp. Sensor Housing - $10
SR Thermostat Housing - $10
SR Coolant Inlet - $10
SR Coolant Complete Setup w/ Sensors - $45


OEM SR20VE P11 Valvetrain (IN+EX Valves, Springs, Cams, Gears)
- 15,000 Miles
- PERFECT!
- MAKE OFFERS ON WHAT YOU NEED!


SR20DET AAC Valve
- PERFECT SHAPE
- $40


S14 SR Valve Cover w/ Coil Pack Cover
- Perfect Shape
- $200


stock KA24de airbox intake system and Filter is still clean (came from a 98' kouki)
- PERFECT SHAPE
- $75


S13 Non-ABS Driveshaft - Pick up only
- Used
- $100


S13 SR Transmision - Pick up only
- Roughly 30k miles
- PERFECT SHAPE
- $150


S13 SR20 Intake Gasket
- PERFECT SHAPE
- $15


S13 SR Bell Housing
- No cracks
- $40


S13 SR release bearing
- Good Condition
- $15


S13 SR Clutch Fork
- Perfect Shape
- $25


SR20 Timing Chain guide
- Perfect Shape
- $10


S13 SR Valve Cover Baffeling
- Great Shape
- $10


SR NGK Iridium Spark Plugs (heat range 8)
- NEW IN BOX
- $30


SR20 Coilpack Gaskets
- NEW
- $3 each


S13 SR20 Valve Cover Gasket
- Perfect Shape
- $20


Injector Gasket O-rings
- Perfect Shape
- $3 each


SR20 Rear Main Seal
- New In Box
- $20

(8) SR20 Hydraulic Lifters
- Perfect Shape
- $5 each


(3) SR OEM Rod
- Great Shape
- $10 each


SR OEM Exhaust Manifold
- Perfect Shape
- $40


SR20det Exhaust Gaskets (t3, T4, Exhaust mani)
- Perfect Shape
- $20


Crank Pulley Bolts (2)
-Perfect Shape
-$5


Transmission Mount Brackets
- Perfect Shape
- $15 each


Alternator Brackets
- Perfect Shape
- $25 each


Knock Sensor (4)...one doesn't have a sub-harness
- Perfect Shape
-$30 each (20 for the one without the sub-harness)


Godspeed Arm - $15
S13 Rear Links - $10 each
S13 Front Lower Control Arm - $30



\/ \/ \/ 350Z PARTS \/ \/ \/

350z LSD
- ~15k miles
- $200


350z OEM Suspension Links
- ~15k miles
- Perfect Shape


350z Master 1 1/16th
- Perfect Shape
- $45


350z Brake Booster
- Perfect Shape
- $100


350z 03' tinted tail lights
- Great shape
- $75


350z OEM Fuel Tank
- ~20k miles
- Perfect Shape
- $90


350z Seats
- ~20k miles
- $300


350z oem Radiator
- ~20k miles
- $100


350z oem Radiator Support
- ~20k miles
- $100




These are all the make an offer items...i dont want or need them so just make an offer...pictures of these upon request.

\/ \/ \/ 2005 WRX (less then 20k miles on items)\/ \/ \/

OEM Air Box Setup
OEM Downpipe
OEM Full Exhaust
OEM Uppipe
OEM Turbo Heat shield

\/ \/ \/ Auto 200SX SER Engine Part Out \/ \/ \/

Head (currently has valves, springs, retainers, and keepers but can remove if buy requests)
Rocker arms
Oil tubes in SR head
Intake and Exhaust cam gears
Valve Cover
EGR valve (in WORKING order)
distributer (in WORKING order)
Headers
Injectors w/ Fuel rail
Water Pump
Water Pump pulley
oil filter block
crank pulley
Intake Manifold (perfect Condition w/ all connectors and hoses)
(3) Pistons
(3) Rods
Coolant tubes
Coolant outlet
Lower Oil Pan
Oil Pan baffling
Timing chain tensioner
Flex Plate
Auto trans gasket
Alternator bracket
intake bracket
power steering bracket
ac bracket
Auto 200sx Engine Harness (completely uncut)
injector harness
tps (throttle position sensor)

Thank You For Looking!

[Imarvin240]

more parts added!

[jeff kelly]

im interested in grabbing a hydraulic lifter

[jerry_beans]

Sell me the hazard button off the ac bezel! Pm me lmk

[Seraphim38]

someday I am going to get off my ass and buy that KU engineering intake manifold. I just don't know if it will do all that much for my GT2871 setup. I have kept my eye on it since you posted it for sale in your original thread.

[SupaDoopa]

How are those rocker arms? Have any cam caps? PM me.

[Imarvin240]

bump to the top

[Imarvin240]

final bump!