Fast question! - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Srjustin · 05-09-2012, 06:43 PM

I got my diff welded on my 240sx. I got it back and can not turn it by hand is this normal? Does it take the power of the car. To turn it? Or did the kid mess my diff up?

NJs13_1993 · 05-09-2012, 08:26 PM

im pretty sure u should be able to turn it from where the drive shaft attaches by hand

KiLLeR2001 · 05-09-2012, 09:12 PM

Holy shit Florida derp strikes again.

brizanden · 05-09-2012, 09:26 PM

welded output shafts.... LIKE A BAUCEEEEE

Srjustin · 05-09-2012, 09:46 PM

Welded out put shaft? That bad? I just wann sure this diff is good, befor i put it in. Ive herd you should be able to turn it by hand. Also ive herd you cant. So plz help i thought this would be simple lol.

brizanden · 05-09-2012, 10:04 PM

you should be able to. u only weld the inside parts (spider gears) sounds like he welded the part that still needs to rotate.

slydin240sx · 05-09-2012, 10:07 PM

Florida. Well that explains it.

OP your diff is fucked!

Srjustin · 05-09-2012, 10:32 PM

Not what i was wanting to here :/. Ok thanx guys. If anyone thinks diffrent let me know.

brizanden · 05-09-2012, 10:41 PM

drain it take the cover off and show us what the insides look like then we can give u a definite answer.

justinbyrant · 05-23-2012, 11:11 PM

the diff is either fucked or it isnt there is no going back, toss it in and leave it jacked up in the rear (on jackstands of coarse) let the clutch out in first, sometimes you can turn them by hand sometimes you cant, if you cant and he welded it right then its only a matter of time before it goes anyways

05-09-2012, 06:43 PM	#1
Srjustin Zilvia Member Join Date: Nov 2011 Location: Fl Age: 35 Posts: 152 Trader Rating: (0) Feedback Score: 0 reviews	Fast question! I got my diff welded on my 240sx. I got it back and can not turn it by hand is this normal? Does it take the power of the car. To turn it? Or did the kid mess my diff up?

05-09-2012, 09:12 PM	#3
KiLLeR2001 Post Whore! Join Date: Jun 2007 Location: オーランドフロリダ Posts: 7,955 Trader Rating: (46) Feedback Score: 46 reviews	Holy shit Florida derp strikes again. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

05-09-2012, 09:26 PM	#4
brizanden Zilvia Addict Join Date: Jan 2009 Location: C-Bus, ohio Age: 35 Posts: 640 Trader Rating: (4) Feedback Score: 4 reviews	welded output shafts.... LIKE A BAUCEEEEE

05-09-2012, 09:46 PM	#5
Srjustin Zilvia Member Join Date: Nov 2011 Location: Fl Age: 35 Posts: 152 Trader Rating: (0) Feedback Score: 0 reviews	Welded out put shaft? That bad? I just wann sure this diff is good, befor i put it in. Ive herd you should be able to turn it by hand. Also ive herd you cant. So plz help i thought this would be simple lol.

05-09-2012, 10:04 PM	#6
brizanden Zilvia Addict Join Date: Jan 2009 Location: C-Bus, ohio Age: 35 Posts: 640 Trader Rating: (4) Feedback Score: 4 reviews	you should be able to. u only weld the inside parts (spider gears) sounds like he welded the part that still needs to rotate.

05-09-2012, 10:07 PM	#7
slydin240sx Zilvia Addict Join Date: Apr 2009 Location: Missouri Posts: 919 Trader Rating: (3) Feedback Score: 3 reviews	Florida. Well that explains it. OP your diff is fucked!

05-09-2012, 10:32 PM	#8
Srjustin Zilvia Member Join Date: Nov 2011 Location: Fl Age: 35 Posts: 152 Trader Rating: (0) Feedback Score: 0 reviews	Not what i was wanting to here :/. Ok thanx guys. If anyone thinks diffrent let me know.

05-09-2012, 10:41 PM	#9
brizanden Zilvia Addict Join Date: Jan 2009 Location: C-Bus, ohio Age: 35 Posts: 640 Trader Rating: (4) Feedback Score: 4 reviews	drain it take the cover off and show us what the insides look like then we can give u a definite answer.

05-23-2012, 11:11 PM	#10
justinbyrant Zilvia Member Join Date: May 2011 Location: eugene Age: 33 Posts: 229 Trader Rating: (0) Feedback Score: 0 reviews	the diff is either fucked or it isnt there is no going back, toss it in and leave it jacked up in the rear (on jackstands of coarse) let the clutch out in first, sometimes you can turn them by hand sometimes you cant, if you cant and he welded it right then its only a matter of time before it goes anyways