transmission install on s13 w/ sr20 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

mrchomponthis · 04-22-2009, 01:12 AM

I am looking for any tips on how to reinstall my transmission i had to put in a new clutch and i had to replace my flywheel bolts and i have my clutch inplace and aligned. I was told to loosen the motor mounts, try putting in the transmission upside down on at a 90 degree angle. I can't seem to get the right and to get the joke in. the top part of the transmission keeps hitting the body of the car and it has become very frustrating. me and 2 of my buddies are planning to get it in tomorrow. PLEASE IF YOU GUYS HAVE ANY OTHER TIPS PLEASE CHIME IN. it would be much appreciated, or if you can lend a helping hand in the process i am in Garden Grove

gunmetalr32 · 04-22-2009, 01:16 AM

i have a trick or two.... try loosening the motor mounts and jack up the front crank pulley with a rubber block till the motor is in a better angle then it should go right in...

gunmetalr32 · 04-22-2009, 01:16 AM

thats if you dont have a crane/cherry picker

mrchomponthis · 04-22-2009, 01:21 AM

i have a cherry picker. wouldn't that damage the crank pulley rapping a chain around it... i also still have all belts on.

gunmetalr32 · 04-22-2009, 01:28 AM

if you have a crane lift up the front of the motor, not by the crank ...

VQMaxFan · 04-22-2009, 02:24 AM

Just put a big block of wood on a jack, and jack up on the motor a little bit from the oil pan.

Get as many ppl as you can to help maneuver the tranny, use a service jack or something to help. What took me and one friend about 2 and a half hours to do, took me and 2 friends 30 minutes to do. Just try to get the trans in as straight as possible!

mrchomponthis · 04-22-2009, 02:27 AM

thanks for the help. i am determined to get this thing in tomorrow. I have seen many threads on doing this but everyone has there own ideas and ways but with NO PICTURES! other people said they just got it in like magic and would never try to do it again.

KiDyNomiTe · 04-22-2009, 05:11 PM

If there is no coolant in it, disconnect the radiator it will tip more, or just take the top mounts out so it tips with the motor.

Keep it turned and it will go in. I did it myself twice, took maybe 30 minutes, well the actual process takes like 40 seconds once you get a burst of energy.

Rapier46 · 04-22-2009, 05:26 PM

lol. take off the shifter and slide it on...its extremely easy.

georgesal · 04-23-2009, 12:21 AM

bang the trans tunnel as close as you can to the motor, you know right where the bell housing hits the tunnel, just hit it with a hammer and then its really easy to put your trans in and out whenever you want.

mrchomponthis · 04-23-2009, 12:23 AM

trans is in thanks for the help

im so stoked right now

SochBAT · 04-23-2009, 01:26 AM

I had a bitch of a time doing it myself.

I was literally bench pressing that fucking tranny.

dmax_silvia_s13 · 04-23-2009, 11:52 AM

Quote:

Originally Posted by Soooshi

I had a bitch of a time doing it myself.

I was literally bench pressing that fucking tranny.

Haha same here it was my first time and I did it by myself. It just takes some patience and some time.
I had a jack under my engine and a tranny jack under the tranny and just jack the engine up and keep trying different things with the tranny and itll eventually go in.
You dont need to turn the tranny 90 degrees thats just for a ka tranny im pretty sure.

Edit: Just saw you got it in so nevermind.

gijoe69 · 04-23-2009, 12:11 PM

lube her up and be sure to drink a couple of beers when installing

mrchomponthis · 04-23-2009, 01:14 PM

i drank plenty of beers and honestly it just slipped right in lol

04-22-2009, 01:12 AM	#1
mrchomponthis Zilvia Addict Join Date: Mar 2009 Location: fghjghjfg Age: 37 Posts: 877 Trader Rating: (11) Feedback Score: 11 reviews	transmission install on s13 w/ sr20 I am looking for any tips on how to reinstall my transmission i had to put in a new clutch and i had to replace my flywheel bolts and i have my clutch inplace and aligned. I was told to loosen the motor mounts, try putting in the transmission upside down on at a 90 degree angle. I can't seem to get the right and to get the joke in. the top part of the transmission keeps hitting the body of the car and it has become very frustrating. me and 2 of my buddies are planning to get it in tomorrow. PLEASE IF YOU GUYS HAVE ANY OTHER TIPS PLEASE CHIME IN. it would be much appreciated, or if you can lend a helping hand in the process i am in Garden Grove

04-22-2009, 01:16 AM	#2
gunmetalr32 Post Whore! Join Date: Jan 2008 Location: oxnard,CA Age: 38 Posts: 3,077 Trader Rating: (14) Feedback Score: 14 reviews	i have a trick or two.... try loosening the motor mounts and jack up the front crank pulley with a rubber block till the motor is in a better angle then it should go right in... __________________ NEED S14 KOUKI VALANCES, S14 NAVAN SIDE SKIRTS, S14 KOUKI OEM JDM LIP HIT ME UP!!

04-22-2009, 01:16 AM	#3
gunmetalr32 Post Whore! Join Date: Jan 2008 Location: oxnard,CA Age: 38 Posts: 3,077 Trader Rating: (14) Feedback Score: 14 reviews	thats if you dont have a crane/cherry picker __________________ NEED S14 KOUKI VALANCES, S14 NAVAN SIDE SKIRTS, S14 KOUKI OEM JDM LIP HIT ME UP!!

04-22-2009, 01:28 AM	#5
gunmetalr32 Post Whore! Join Date: Jan 2008 Location: oxnard,CA Age: 38 Posts: 3,077 Trader Rating: (14) Feedback Score: 14 reviews	if you have a crane lift up the front of the motor, not by the crank ... __________________ NEED S14 KOUKI VALANCES, S14 NAVAN SIDE SKIRTS, S14 KOUKI OEM JDM LIP HIT ME UP!!

04-22-2009, 05:11 PM	#8
KiDyNomiTe Post Whore! Join Date: Mar 2002 Location: Chicago Age: 38 Posts: 6,296 Trader Rating: (0) Rides Gallery: KiDyNomiTe Feedback Score: 0 reviews	If there is no coolant in it, disconnect the radiator it will tip more, or just take the top mounts out so it tips with the motor. Keep it turned and it will go in. I did it myself twice, took maybe 30 minutes, well the actual process takes like 40 seconds once you get a burst of energy. __________________ PROCEED Grip Gambler

04-22-2009, 01:21 AM	#4
mrchomponthis Zilvia Addict Join Date: Mar 2009 Location: fghjghjfg Age: 37 Posts: 877 Trader Rating: (11) Feedback Score: 11 reviews	i have a cherry picker. wouldn't that damage the crank pulley rapping a chain around it... i also still have all belts on.

04-22-2009, 02:24 AM	#6
VQMaxFan Zilvia Junkie Join Date: May 2008 Location: Mobile AL Age: 35 Posts: 464 Trader Rating: (3) Feedback Score: 3 reviews	Just put a big block of wood on a jack, and jack up on the motor a little bit from the oil pan. Get as many ppl as you can to help maneuver the tranny, use a service jack or something to help. What took me and one friend about 2 and a half hours to do, took me and 2 friends 30 minutes to do. Just try to get the trans in as straight as possible!

04-22-2009, 02:27 AM	#7
mrchomponthis Zilvia Addict Join Date: Mar 2009 Location: fghjghjfg Age: 37 Posts: 877 Trader Rating: (11) Feedback Score: 11 reviews	thanks for the help. i am determined to get this thing in tomorrow. I have seen many threads on doing this but everyone has there own ideas and ways but with NO PICTURES! other people said they just got it in like magic and would never try to do it again.

04-22-2009, 05:26 PM	#9
Rapier46 Zilvia Member Join Date: Oct 2008 Location: Calgary Age: 34 Posts: 260 Trader Rating: (0) Feedback Score: 0 reviews	lol. take off the shifter and slide it on...its extremely easy. __________________ Left hand drive 240sx's ARE NOT SILVIAS.

04-23-2009, 12:21 AM	#10
georgesal BANNED Join Date: Oct 2006 Location: Los Angeles Age: 40 Posts: 842 Trader Rating: (2) Feedback Score: 2 reviews	bang the trans tunnel as close as you can to the motor, you know right where the bell housing hits the tunnel, just hit it with a hammer and then its really easy to put your trans in and out whenever you want.

04-23-2009, 12:23 AM	#11
mrchomponthis Zilvia Addict Join Date: Mar 2009 Location: fghjghjfg Age: 37 Posts: 877 Trader Rating: (11) Feedback Score: 11 reviews	trans is in thanks for the help im so stoked right now

04-23-2009, 01:26 AM	#12
SochBAT Post Whore! Join Date: Dec 2004 Location: Abilene, TX Age: 39 Posts: 6,428 Trader Rating: (9) Rides Gallery: SochBAT Feedback Score: 9 reviews	I had a bitch of a time doing it myself. I was literally bench pressing that fucking tranny.

04-23-2009, 12:11 PM	#14
gijoe69 Zilvia Junkie Join Date: May 2003 Location: San Francisco, CA Age: 40 Posts: 366 Trader Rating: (1) Feedback Score: 1 reviews	lube her up and be sure to drink a couple of beers when installing

04-23-2009, 01:14 PM	#15
mrchomponthis Zilvia Addict Join Date: Mar 2009 Location: fghjghjfg Age: 37 Posts: 877 Trader Rating: (11) Feedback Score: 11 reviews	i drank plenty of beers and honestly it just slipped right in lol