How do you install a Driver Side Window on s14???? - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

jakal · 02-12-2007, 06:15 AM

okay, i just bought a window for my 95 s14....it should come i hope, but i was wondering how the hell do you install a driver side window??? anyone know how to?? it would be much appreciated and i would save 150.00......thanks in advance!

body: 1995 240sx NON SE (meaning 4 Lugs, NO LSD)

projectRDM · 02-12-2007, 10:03 AM

Two M6 nuts on the bottom of the glass. There's a stop at each side on top of the door you might need to adjust, otherwise if you can't do it by just looking at it you need to find another hobby. It's simple.

contranication · 02-12-2007, 10:38 AM

It also helps to move the window up and down so you can line up the regulator with the holes in the door to tighten the nuts... besides that you might need someone to hold the window for you

SDS13COUPE · 02-12-2007, 11:01 AM

It's simple. ( I have an S13 so it may vary)
-Remove the door panel, it has a screw in the handle, and possibly another under a cover near the door jam
-Remove the plastic film with the white shit all over it
-Move the window up a little to reach the 10mm bolts holding it to the track
-Unbolt them and tilt window forward to pull up and out of the door
-Make sure to align the window in the guides on the sides and try not to scratch it, and don't overtighten the bolts
-Then do it all in reverse and you should be kosher. Like I said I have an S13 so it may be a little different but if you have some mechanical knowledge you should be fine. GL and if you have any questions just ask. Peace

02-12-2007, 06:15 AM	#1
jakal Leaky Injector Join Date: Sep 2006 Location: Savannah, GA Age: 37 Posts: 125 Trader Rating: (0) Feedback Score: 0 reviews	How do you install a Driver Side Window on s14???? okay, i just bought a window for my 95 s14....it should come i hope, but i was wondering how the hell do you install a driver side window??? anyone know how to?? it would be much appreciated and i would save 150.00......thanks in advance! body: 1995 240sx NON SE (meaning 4 Lugs, NO LSD)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-12-2007, 10:03 AM	#2
projectRDM Post Whore! Join Date: Dec 2002 Location: Atlanta Age: 51 Posts: 13,812 Trader Rating: (12) Feedback Score: 12 reviews	Two M6 nuts on the bottom of the glass. There's a stop at each side on top of the door you might need to adjust, otherwise if you can't do it by just looking at it you need to find another hobby. It's simple.

02-12-2007, 10:38 AM	#3
contranication Zilvia Member Join Date: Jun 2004 Location: West palm Posts: 165 Trader Rating: (0) Feedback Score: 0 reviews	It also helps to move the window up and down so you can line up the regulator with the holes in the door to tighten the nuts... besides that you might need someone to hold the window for you

02-12-2007, 11:01 AM	#4
SDS13COUPE Zilvia FREAK! Join Date: May 2006 Location: San Diego Age: 39 Posts: 1,403 Trader Rating: (19) Feedback Score: 19 reviews	It's simple. ( I have an S13 so it may vary) -Remove the door panel, it has a screw in the handle, and possibly another under a cover near the door jam -Remove the plastic film with the white shit all over it -Move the window up a little to reach the 10mm bolts holding it to the track -Unbolt them and tilt window forward to pull up and out of the door -Make sure to align the window in the guides on the sides and try not to scratch it, and don't overtighten the bolts -Then do it all in reverse and you should be kosher. Like I said I have an S13 so it may be a little different but if you have some mechanical knowledge you should be fine. GL and if you have any questions just ask. Peace