PS banjo bolt - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

iamwesley · 01-22-2006, 01:45 AM

Where can I get one with washers?

aznpoopy · 01-22-2006, 01:52 AM

junkyard.
nissan dealer.

if you have the bolt, just buy the washers seperately from the dealer.

IAM_SO_sLOw · 01-22-2006, 02:16 AM

i say just go to a junkyard and pocket it lol

DoriftoSlut · 01-22-2006, 02:39 AM

you can get them at autoparts stores cost. cost is low and its brand new.

kingsol · 01-22-2006, 02:42 AM

i believe the dealer charges $60 for the bolt alone and a stuipid dumb amount for the washers which you could get from home depot. i remember asking for two bolts for the pump and misc. nothings and they charged $180...

Suk02Si · 01-22-2006, 04:36 AM

For which motor? The mount for the dohc was diff than the one for th SR

The one off my SR (left) has a slight angle to it. I have the stock dohc one (right) if you need it.

kingsol · 01-22-2006, 09:18 AM

they both work with the sr pump

sidious141 · 01-22-2006, 09:19 PM

Quote:

Originally Posted by IAM_SO_sLOw

i say just go to a junkyard and pocket it lol

2nd that, just make shure you hide it well

FRpilot · 01-23-2006, 04:07 AM

Quote:

Originally Posted by aznpoopy

if you have the bolt, just buy the washers seperately from the dealer.

aren't the washers thin copper washers? only dealer sells these?

projectRDM · 01-23-2006, 08:14 AM

Quote:

Originally Posted by FRpilot

aren't the washers thin copper washers? only dealer sells these?

No, as mentioned above any auto parts store will have them in numerous sizes.

aznpoopy · 01-23-2006, 09:15 AM

from my understanding the washers are a 'special' size so when you torque down the bolt, the opening in the banjo bolt aligns properly.

after doing it... IMO if you get any old set of washers, you could probably just overtorque the bolt a little to get it to line up properly.

Dousan_PG · 01-23-2006, 11:41 AM

not true
i used autozone ones and its fine. no leaks

01-22-2006, 01:45 AM	#1
iamwesley Zilvia Member Join Date: May 2003 Location: socal Posts: 150 Trader Rating: (0) Feedback Score: 0 reviews	PS banjo bolt Where can I get one with washers?

01-22-2006, 02:39 AM	#4
DoriftoSlut Nissanaholic! Join Date: Nov 2002 Location: SoCal and Hawaii Age: 41 Posts: 1,986 Trader Rating: (0) Feedback Score: 0 reviews	you can get them at autoparts stores cost. cost is low and its brand new. __________________ Death Before Dishonor. www.pinkgodzira.com www.driftalliance.com

01-22-2006, 02:42 AM	#5
kingsol Zilvia FREAK! Join Date: Jun 2003 Location: Berkeley/San Francisco Posts: 1,435 Trader Rating: (0) Feedback Score: 0 reviews	i believe the dealer charges $60 for the bolt alone and a stuipid dumb amount for the washers which you could get from home depot. i remember asking for two bolts for the pump and misc. nothings and they charged $180... __________________ There is a time in every man's education when he arrives at the conviction that envy is ignorance; that imitation is suicide; that he must take himself for better for worse as his portion; that though the wide universe is full of good, no kernel of nourishing corn can come to him but through his toil bestowed on that plot of ground which is given to him to till. -Emerson

01-22-2006, 09:18 AM	#7
kingsol Zilvia FREAK! Join Date: Jun 2003 Location: Berkeley/San Francisco Posts: 1,435 Trader Rating: (0) Feedback Score: 0 reviews	they both work with the sr pump __________________ There is a time in every man's education when he arrives at the conviction that envy is ignorance; that imitation is suicide; that he must take himself for better for worse as his portion; that though the wide universe is full of good, no kernel of nourishing corn can come to him but through his toil bestowed on that plot of ground which is given to him to till. -Emerson

01-23-2006, 11:41 AM	#12
Dousan_PG Post Whore! Join Date: May 2002 Location: Orange County, California Age: 46 Posts: 16,640 Trader Rating: (23) Rides Gallery: Dousan_PG Feedback Score: 23 reviews	not true i used autozone ones and its fine. no leaks __________________ Aaron Pink GodziRa www.geocities.com/pink_godzira

01-22-2006, 01:52 AM	#2
aznpoopy Post Whore! Join Date: Mar 2003 Location: New Jersey Age: 44 Posts: 5,013 Trader Rating: (1) Feedback Score: 1 reviews	junkyard. nissan dealer. if you have the bolt, just buy the washers seperately from the dealer.

01-22-2006, 02:16 AM	#3
IAM_SO_sLOw Zilvia FREAK! Join Date: Apr 2004 Location: west covina Posts: 1,164 Trader Rating: (5) Feedback Score: 5 reviews	i say just go to a junkyard and pocket it lol

01-22-2006, 04:36 AM	#6
Suk02Si Zilvia Addict Join Date: Dec 2004 Location: Los Angeles Age: 42 Posts: 831 Trader Rating: (8) Feedback Score: 8 reviews	For which motor? The mount for the dohc was diff than the one for th SR The one off my SR (left) has a slight angle to it. I have the stock dohc one (right) if you need it.

01-23-2006, 09:15 AM	#11
aznpoopy Post Whore! Join Date: Mar 2003 Location: New Jersey Age: 44 Posts: 5,013 Trader Rating: (1) Feedback Score: 1 reviews	from my understanding the washers are a 'special' size so when you torque down the bolt, the opening in the banjo bolt aligns properly. after doing it... IMO if you get any old set of washers, you could probably just overtorque the bolt a little to get it to line up properly.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode