95 S14 5spd conversion - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

jin8544 · 03-01-2007, 07:49 PM

Can i do it?
and how can i do it?
what are the things that i need?
Im thinking about buying auto and convert it to 5spd

Akiros · 03-01-2007, 08:01 PM

depends on the person / search / search / good for you

sTalnOut · 03-01-2007, 08:05 PM

wat do u wanna dooooooooo ?

jin8544 · 03-02-2007, 12:15 AM

i want to go from auto to manuel

azndummie · 03-02-2007, 12:21 AM

well if u wanna go from an auto to a mexican thats kinda hard. u gotta find a manuel first.

sw20>>s14 · 03-02-2007, 01:09 AM

FAQ!!!!

lookaroundjeez

drftwerks · 03-02-2007, 01:10 AM

honestly if you have to ask, you probably shouldnt try it

*NemeGuero* · 03-02-2007, 01:13 AM

Quote:

Originally Posted by azndummie

well if u wanna go from an auto to a mexican thats kinda hard. u gotta find a manuel first.

I got a cousin Manuel. hahha

nrg · 03-02-2007, 02:13 AM

need:
5 speed tranny and mount
clutch kit with pilot bearing and 5 speed flywheel
slave cylinder, clutch hard lines, master cylinder, clutch peddle assembly
5 speed driveshaft

extra: 5 speed brake peddle assembly or just cut your automatic one (it will sit higher than the clutch peddle).
manual shifter trim and boot.

Your 5 speed tranny shouldn't have any oil in it, if it does; drain it.

drain tranny oil, unbolt drive shaft, unlink the shifter cable, remove oil lines to radiator, unplug wires to sensors on tranny, unbolt the tranny from the motor, unbolt the tranny mount. drop the tranny, remove engine under cover to access the 4 bolt holding the torque converter, pull out the automatic pilot bearing.
put on 5 speed fly wheel, pop on the manual pilot bearing, put on the new clutch, greese the pilot bearing hole, put on the new throwout bearing on the tranny and greese the clutch fork pivot ball. put the 5 speed tranny on, mount the tranny mount and driveshaft.
Get into the car and remove the shifter assembly, tape up the shift lock cable in OPEN position (so you can remove the key, you can pull it all out if you want). Pour 2.5 quarts of GL4 gear oil (redline mt90) into the tranny and mount the shifter, mount the boot and ring, now mount the shifter boot and trim.
Go under the driver side dash and cut a hole for the clutch master cylinder, there are indentions for it. Pull the automatic trans ECU down there too. Once done, mount the clutch peddle assembly and master cylinder, install the hard lines, Under the car, bend the lines so it faces the slave cylinder if neccessary (sometimes they're facing towards the back of the car because of a damping line). Bleed the slave cylinder and attack the wiring.

http://www.ka24development.com/cwilf...lectrical.html

EAS13 · 03-02-2007, 09:37 AM

Search!!! You will get hammered if you don't spend 1-5minutes finding info on this forum for yourself.

I'll be nice, here's all the info you need:
http://www.zilvia.net/f/showthread.php?t=21181

kenshinS14sks · 03-02-2007, 10:22 AM

Quote:

Originally Posted by jin8544

i want to go from auto to manuel

Quote:

Originally Posted by azndummie

well if u wanna go from an auto to a mexican thats kinda hard. u gotta find a manuel first.

holy jesus on a bike i was thinking the SAME THING!!!

03-01-2007, 07:49 PM	#1
jin8544 Zilvia Junkie Join Date: Feb 2007 Location: Carbondale IL Posts: 458 Trader Rating: (6) Feedback Score: 6 reviews	95 S14 5spd conversion Can i do it? and how can i do it? what are the things that i need? Im thinking about buying auto and convert it to 5spd

03-02-2007, 12:21 AM	#5
azndummie Zilvia FREAK! Join Date: Dec 2005 Location: orange county Posts: 1,362 Trader Rating: (14) Feedback Score: 14 reviews	well if u wanna go from an auto to a mexican thats kinda hard. u gotta find a manuel first. __________________

03-02-2007, 01:09 AM	#6
sw20>>s14 Post Whore! Join Date: Jan 2005 Location: bay area Posts: 5,656 Trader Rating: (19) Feedback Score: 19 reviews	FAQ!!!! lookaroundjeez __________________ s14\| y34\| 911 gts\| exige s\| 600rr\| r3\| 250r\| 85 girlfriend

03-02-2007, 01:10 AM	#7
drftwerks Nissanaholic! Join Date: Mar 2004 Location: california Posts: 2,343 Trader Rating: (1) Feedback Score: 1 reviews	honestly if you have to ask, you probably shouldnt try it __________________ giantroboteyes.wordpress.com/

03-02-2007, 02:13 AM	#9
nrg Zilvia FREAK! Join Date: Mar 2004 Location: CA Age: 40 Posts: 1,571 Trader Rating: (1) Feedback Score: 1 reviews	need: 5 speed tranny and mount clutch kit with pilot bearing and 5 speed flywheel slave cylinder, clutch hard lines, master cylinder, clutch peddle assembly 5 speed driveshaft extra: 5 speed brake peddle assembly or just cut your automatic one (it will sit higher than the clutch peddle). manual shifter trim and boot. Your 5 speed tranny shouldn't have any oil in it, if it does; drain it. drain tranny oil, unbolt drive shaft, unlink the shifter cable, remove oil lines to radiator, unplug wires to sensors on tranny, unbolt the tranny from the motor, unbolt the tranny mount. drop the tranny, remove engine under cover to access the 4 bolt holding the torque converter, pull out the automatic pilot bearing. put on 5 speed fly wheel, pop on the manual pilot bearing, put on the new clutch, greese the pilot bearing hole, put on the new throwout bearing on the tranny and greese the clutch fork pivot ball. put the 5 speed tranny on, mount the tranny mount and driveshaft. Get into the car and remove the shifter assembly, tape up the shift lock cable in OPEN position (so you can remove the key, you can pull it all out if you want). Pour 2.5 quarts of GL4 gear oil (redline mt90) into the tranny and mount the shifter, mount the boot and ring, now mount the shifter boot and trim. Go under the driver side dash and cut a hole for the clutch master cylinder, there are indentions for it. Pull the automatic trans ECU down there too. Once done, mount the clutch peddle assembly and master cylinder, install the hard lines, Under the car, bend the lines so it faces the slave cylinder if neccessary (sometimes they're facing towards the back of the car because of a damping line). Bleed the slave cylinder and attack the wiring. http://www.ka24development.com/cwilf...lectrical.html __________________ driftingisgay.com

03-01-2007, 08:01 PM	#2
Akiros Zilvia FREAK! Join Date: May 2005 Location: Arkansas Age: 36 Posts: 1,242 Trader Rating: (1) Feedback Score: 1 reviews	depends on the person / search / search / good for you

03-01-2007, 08:05 PM	#3
sTalnOut Zilvia Member Join Date: Jun 2006 Location: crooklyn,NYC Age: 41 Posts: 286 Trader Rating: (2) Feedback Score: 2 reviews	wat do u wanna dooooooooo ?

03-02-2007, 12:15 AM	#4
jin8544 Zilvia Junkie Join Date: Feb 2007 Location: Carbondale IL Posts: 458 Trader Rating: (6) Feedback Score: 6 reviews	i want to go from auto to manuel

03-02-2007, 09:37 AM	#10
EAS13 Leaky Injector Join Date: Aug 2005 Location: LA Posts: 145 Trader Rating: (0) Feedback Score: 0 reviews	Search!!! You will get hammered if you don't spend 1-5minutes finding info on this forum for yourself. I'll be nice, here's all the info you need: http://www.zilvia.net/f/showthread.php?t=21181