CA 1st GEN APEXi S-AFC... RARE - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

TheWayItGoes909 · 03-31-2010, 03:50 PM

For Sale 1st gen Apexi S-AFC Selling AS IS Never Installed.

(1st Gen) complete with wire harness. Basically what the S-AFC does is alter the voltage the ECU receives from the MAF/MAP sensor. This causes the air/fuel mixture to either go leaner (-) or richer (+).You can adjust in increments of 2%.You can fine-tune the mixture at different RPM points (800rpm, 2400rpm, 4000rpm, 5600rpm, 7200rpm).

Please consult a professional for installation.

Size: 12cm x 13cm, *1 inch = 25.4 mm = 2.54 cm.

BUY BUY BUY

$120 Shipped + Paypal Fees

Local's PM for price

TheWayItGoes909 · 04-01-2010, 10:41 PM

HOW TO SET FOR SR20DET (taken from FreshAlloy)
Set the switches on the back to
uudddudu
(u = up, d=down)
If you have a stock SR MAF set the vehicle to 6 on the setting wheel.
If you have a z32 MAF(and ECU tuned for a z32 MAF) set it to 2
AFC wires:
Red -- connect to power source
BLK-- connect to gnd (prefferablt the MAF gnd)
Green -- tap into RPM wire
Yellow to ECU (cut MAF signal wire)
White from MAF (cut MAF signal wire)
Blue -- no use

TheWayItGoes909 · 04-09-2010, 06:49 PM

MOUNTS NICELY

03-31-2010, 03:50 PM	#1
TheWayItGoes909 Zilvia Junkie Join Date: Sep 2008 Location: Inland Empire Posts: 382 Trader Rating: (10) Feedback Score: 10 reviews	1st GEN APEXi S-AFC... RARE For Sale 1st gen Apexi S-AFC Selling AS IS Never Installed. (1st Gen) complete with wire harness. Basically what the S-AFC does is alter the voltage the ECU receives from the MAF/MAP sensor. This causes the air/fuel mixture to either go leaner (-) or richer (+).You can adjust in increments of 2%.You can fine-tune the mixture at different RPM points (800rpm, 2400rpm, 4000rpm, 5600rpm, 7200rpm). Please consult a professional for installation. Size: 12cm x 13cm, 1 inch = 25.4 mm = 2.54 cm. BUY BUY BUY* $120 Shipped + Paypal Fees Local's PM for price

04-01-2010, 10:41 PM	#2
TheWayItGoes909 Zilvia Junkie Join Date: Sep 2008 Location: Inland Empire Posts: 382 Trader Rating: (10) Feedback Score: 10 reviews	HOW TO SET FOR SR20DET (taken from FreshAlloy) Set the switches on the back to uudddudu (u = up, d=down) If you have a stock SR MAF set the vehicle to 6 on the setting wheel. If you have a z32 MAF(and ECU tuned for a z32 MAF) set it to 2 AFC wires: Red -- connect to power source BLK-- connect to gnd (prefferablt the MAF gnd) Green -- tap into RPM wire Yellow to ECU (cut MAF signal wire) White from MAF (cut MAF signal wire) Blue -- no use

04-09-2010, 06:49 PM	#3
TheWayItGoes909 Zilvia Junkie Join Date: Sep 2008 Location: Inland Empire Posts: 382 Trader Rating: (10) Feedback Score: 10 reviews	MOUNTS NICELY