ASP Pulley Problem - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

punxva · 09-26-2007, 11:24 PM

ok after much searching and busting me ass, i can't figure this out. when trying to install my pulley, it goes on almost all the way, then is off by like 4mm from lining up with the others, i don't have an impact, so i'm not sure if it'll go on any further that way, but there is an oval like washer thats on the crank, near the housing, which to me might be why its not going in all the, way, anyone else have any insight to this, here's the best picture i could take showing what i'm talking about... i've got it circled...

Jung918 · 09-27-2007, 01:10 AM

replace your front main seal.
I don't remember seeing a washer when I installed my pulley.

punxva · 09-27-2007, 06:34 AM

would my front main seal be causing it not to go in all the way? heres a picture of it with the power steering belt on but not tight, you can see that it needs to come back a little bit more, the bolt on it is also not torqued down, if i got an impact and used that would that do the trick?

I know it's really hard to see from those pics, but you can see that the crank pulley needs to go back just a tad bit

punxva · 09-27-2007, 07:20 AM

ok sorry here's 2 better pictures....

punxva · 09-27-2007, 09:41 AM

update, tried to impact it on there, and it still wont go in any further, i can see the lip of where it's supposed to go into, and it just wont go any further

NAGODRIFTER · 09-27-2007, 02:22 PM

Looks like maybe the oil-thrower for the crank seal.. look at this site http://www.courtesyparts.com/betasit...1420_1428.html
I think it is supposed to be on the other side of the seal? part #12302.. I would change the seal while I was at it anyways.. and then look closer at the part in question..
Have you measured the depth of each pulley where it mounts to the crankshaft?? I would take a few minutes and do that first..

bo2o · 01-08-2008, 05:34 AM

did you ever get the pulley on?

punxva · 01-09-2008, 06:08 AM

no, i called asp and it was for a sohc

los_inc · 01-09-2008, 07:08 AM

sell it to me <3
-los

punxva · 01-09-2008, 08:47 AM

make an offer man, it's just sitting in my room

09-27-2007, 01:10 AM	#2
Jung918 Post Whore! Join Date: Oct 2003 Location: CA Posts: 3,203 Trader Rating: (2) Feedback Score: 2 reviews	replace your front main seal. I don't remember seeing a washer when I installed my pulley. __________________ Sale: Hello Kitty Horn Button S14 Rear Valences K.Y. Gordon the Thief (Tony Chen)

01-08-2008, 05:34 AM	#7
bo2o Zilvia FREAK! Join Date: May 2006 Location: 626 socal! Posts: 1,315 Trader Rating: (7) Feedback Score: 7 reviews	did you ever get the pulley on? __________________ fS! *vlsd ! slim fans ! hid kits ! lug nuts !* http://www.zilvia.net/f/search.php?d...earchuser=bo2o ^^^click^^^

01-09-2008, 07:08 AM	#9
los_inc Zilvia Addict Join Date: Apr 2006 Location: New Joisey Bro. Age: 40 Posts: 826 Trader Rating: (15) Feedback Score: 15 reviews	sell it to me <3 -los __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-27-2007, 02:22 PM	#6
NAGODRIFTER Join Date: Jul 2007 Location: Nor-Cal Age: 49 Posts: 10 Trader Rating: (0) Feedback Score: 0 reviews	Looks like maybe the oil-thrower for the crank seal.. look at this site http://www.courtesyparts.com/betasit...1420_1428.html I think it is supposed to be on the other side of the seal? part #12302.. I would change the seal while I was at it anyways.. and then look closer at the part in question.. Have you measured the depth of each pulley where it mounts to the crankshaft?? I would take a few minutes and do that first..