NC S13-S14 DriftSpec Suspension parts - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

JDS Performance · 02-16-2009, 07:37 PM

Quote:

Originally Posted by Def

I'd double check the toe link fitting on an S14. They are not interchangable between the S13 and S14. S14s are 50mm wide at the subframe mounting point, the S13 uses a 40mm wide mount.

I have the same type toe rods, and had to lathe up new bushings for it to fit my new S14 subframe.

Not saying your wrong - but maybe you had a different brand?

I have had this brand on a s13 & s14 with no problems - I did not notice any play on the s14?

Def · 02-16-2009, 07:50 PM

The subframe mounting point is 10 mm wider on the S14 for the toe link is all I'm saying. The arms are not directly interchangable.

JDS Performance · 02-16-2009, 07:58 PM

Quote:

Originally Posted by Def

The subframe mounting point is 10 mm wider on the S14 for the toe link is all I'm saying. The arms are not directly interchangable.

and you are posative your s13 or s14 subframe wasnt off? 10mm isnt a huge deal to begin with.

Next time I have the 2 aprt I will measure myself.

Its funny that everyone sells the same parts for both chassis though?

boske · 02-17-2009, 04:12 AM

Couldn't you throw on some SS washers to take up the 10mm? Maybe I'm missing something?

JDS Performance · 02-17-2009, 05:00 AM

Quote:

Originally Posted by boske

Couldn't you throw on some SS washers to take up the 10mm? Maybe I'm missing something?

yes you could - the walls of the subframe would pull close that much when you torque down the parts too.

He is just letting us know - thats all - and I thank him for that. Good looking out.

JDS Performance · 02-21-2009, 01:27 PM

S14 RUCAs will not fit the S13 - Just found this out. Post changed!

JDS Performance · 01-30-2010, 02:32 PM

Back from the dead - I have a few sets left - just cleaning the garage out

02-21-2009, 01:27 PM	#6
JDS Performance Zilvia.net Advertiser Join Date: Jul 2006 Location: Concord, NC Posts: 3,127 Trader Rating: (53) Feedback Score: 53 reviews	S14 RUCAs will not fit the S13 - Just found this out. Post changed! __________________ http://www.240SXTECHDVDS.org http://www.JDSPerformanceTurbos.com

01-30-2010, 02:32 PM	#7
JDS Performance Zilvia.net Advertiser Join Date: Jul 2006 Location: Concord, NC Posts: 3,127 Trader Rating: (53) Feedback Score: 53 reviews	Back from the dead - I have a few sets left - just cleaning the garage out __________________ http://www.240SXTECHDVDS.org http://www.JDSPerformanceTurbos.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

02-16-2009, 07:50 PM	#2
Def Post Whore! Join Date: Apr 2004 Location: Houston, TX Posts: 2,701 Trader Rating: (16) Feedback Score: 16 reviews	The subframe mounting point is 10 mm wider on the S14 for the toe link is all I'm saying. The arms are not directly interchangable.

02-17-2009, 04:12 AM	#4
boske Zilvia Member Join Date: Jul 2008 Location: PA Age: 39 Posts: 230 Trader Rating: (8) Feedback Score: 8 reviews	Couldn't you throw on some SS washers to take up the 10mm? Maybe I'm missing something?