Wheel Fitment Question Thread

[Frankz91]

Wat can be done about this
I wanna get it fixed so I can slam my 240 & pull or roll my fenders evenly

[zooopreme]

Originally Posted by Frankz91

Wat can be done about this
I wanna get it fixed so I can slam my 240 & pull or roll my fenders evenly

Not really possible unless you start playing around with your alignment. Pull according to what your car needs.

[silviaNC]

So i decide to go with either varrstoen 1.1 or 2.2
18x9.5 +22
18x 10.5+30
Stanze coilovers
What tires set up will work?
They are going on a s14 with z32/z33 rotors. Fenders rolled and minimal pull
Was thinking
245/35/18 up front
285/30/18 on back
Thanks for the help.

[fliprayzin240sx]

^^^Sounds good, should work. But if you pull the front a bit more, you can fit 255s. Rears, have you found tires that has those sizing? I dont remember ever finding 30 series 18s.

[g_mac530]

Ok, guys. I have 50mm chargespeeds on the way. I'm looking to go mmore aggressive with my wheel setup. So I have come across a few setups for sale here. My question is, how far can rear overs be "bowed" out? I have seen many different setups run with the overs, and all I'm really going by right now is pictures which is not the best thing to do.

I figure if I go aggressive I might as well get a setup that I will bow the fenders to make fit instead on getting a less aggressive wheel and messing around with spacers and whatnot. I'm also not looking to run a crazy amount of camber either.

I was thinking about picking up some Equips but the rear sizing is 18x13 -18 I believe. Now, I have seen another s14 with the Chargespeeds running an 18x13 -10 Wed wheel. Doesn't look like too much camber, but the car is also way lower than I am. I tried contacting the owner about alignment specs but have gotten no answer. So any help from the overfender experts would be appreciated. Thanks.

[JN1AS4]

Any advice about me running 18x9 +25 255/40/18 on all 4 corners. I drive a stock body s13 coupe with megan coilovers/RUCA. Spacers shouldn't be needed should they? And I want to run the minimum amount of -camber possible. I know that a roll/pull will probably be needed but nothing to drastic. Any advice would be appreciated.

[silviaNC]

Originally Posted by fliprayzin240sx

^^^Sounds good, should work. But if you pull the front a bit more, you can fit 255s. Rears, have you found tires that has those sizing? I dont remember ever finding 30 series 18s.

Ordered 255/35 and 275/35 hankook.
Falken has 285^30 avaiable and i believe federal as well. I think i might need a 5mm spacer for the front. What u think?

[RB725]

getting ready to make a a purchase wanted to talk to some knowledgable about the s14 chassis, Rims in mind XXR 526 18x10.5 +20 on the rears, im trying to run at least a 265 or 275 tire with hopes of fitting a 305 . I used the wheel calculator and according to this it states inner clearance 1 MM more, im assuming that means I need one mm more as in a spacer?? and for the outer extend an extra 39mm. Im a little lost. Can someone shed some light on my situation. I wanna run some wicked wide tires but not hella flush bullshit or tires sticking out of my vehicle by 2 feet either. If fenders need to be rolled sweet otherwise what do I do.....besides choose different wheels!!

[fliprayzin240sx]

Originally Posted by g_mac530

Ok, guys. I have 50mm chargespeeds on the way. I'm looking to go mmore aggressive with my wheel setup. So I have come across a few setups for sale here. My question is, how far can rear overs be "bowed" out? I have seen many different setups run with the overs, and all I'm really going by right now is pictures which is not the best thing to do.

I figure if I go aggressive I might as well get a setup that I will bow the fenders to make fit instead on getting a less aggressive wheel and messing around with spacers and whatnot. I'm also not looking to run a crazy amount of camber either.

I was thinking about picking up some Equips but the rear sizing is 18x13 -18 I believe. Now, I have seen another s14 with the Chargespeeds running an 18x13 -10 Wed wheel. Doesn't look like too much camber, but the car is also way lower than I am. I tried contacting the owner about alignment specs but have gotten no answer. So any help from the overfender experts would be appreciated. Thanks.

Personally, I would have looked for 70mm in the rear just to be safe. You can't really just throw a random number out there and say well they should bow out 50mm more. All depends on how thick the fiberglass is and what the actual measurements of the fender really are. Just cuz they said 50mm, doesnt mean its exactly 50mm.

Also, which Chargespeed fenders?

Originally Posted by JN1AS4

Any advice about me running 18x9 +25 255/40/18 on all 4 corners. I drive a stock body s13 coupe with megan coilovers/RUCA. Spacers shouldn't be needed should they? And I want to run the minimum amount of -camber possible. I know that a roll/pull will probably be needed but nothing to drastic. Any advice would be appreciated.

Should clear no problem...

Originally Posted by silviaNC

Ordered 255/35 and 275/35 hankook.
Falken has 285^30 avaiable and i believe federal as well. I think i might need a 5mm spacer for the front. What u think?

Wont really know till you put it on. If you dont want to run spacers, you can always slot the strut/knuckle mount out so you can pull the knuckles away from the strut.

Originally Posted by delado

Trying to order some tires for my kouki at the moment but I'm in a bit of a pickle.

Rears are 18x10.5 +22

Fronts are 18X9.5 +12

I'm on Stance GR+

Ideally I would want to run a 225/40 up front and a 265/35 in the rear. (Achilles ATR Sport)

My overall goal is to run minimum camber in the rear. I don't mind running lots of camber in the front. I would also like to keep my metal virgin. I don't mind rolling the lip in but I would like to avoid a pull. I know I won't have issues in the front. But the rear does concern me. What do you fellas think?

Considering how wide of a tires you want, you'd need to pull the rears if you dont want to run alot of camber.

Originally Posted by xsephish

Would
17x9 +12 offset fronts
17x9.5 +12 offset rears
fit on stock metal with just a good roll possibly slight pull or raise the car some?
I have stance gr + pro coils spl rucas
also what ideal tire size on this? I don't want a stretch i want as much tire as i can fit while not throwing the speedo off much if any.

Well, you need to make up your mind. Are you gonna lower the car and have tires within 1" of the fenders? If YES, then you'd need to stretch som tires. 225/45-17s all around. If you also want to run wider tires than that, you'd need to pull the fenders or run camber. I'd go with something like 235/40-17 up front and 245/40-17 in the rear.

Originally Posted by RB725

getting ready to make a a purchase wanted to talk to some knowledgable about the s14 chassis, Rims in mind XXR 526 18x10.5 +20 on the rears, im trying to run at least a 265 or 275 tire with hopes of fitting a 305 . I used the wheel calculator and according to this it states inner clearance 1 MM more, im assuming that means I need one mm more as in a spacer?? and for the outer extend an extra 39mm. Im a little lost. Can someone shed some light on my situation. I wanna run some wicked wide tires but not hella flush bullshit or tires sticking out of my vehicle by 2 feet either. If fenders need to be rolled sweet otherwise what do I do.....besides choose different wheels!!

No, the calculator is using whatever wheel specs you put in originally and calculating how the new wheels will fit in reference to that. So with the calculator saying that you will get 1mm more clearance inside, its saying the wheel lip inside of the new rim will be 1mm more AWAY from the suspension. So you actually gain more space inside. The outer extending an extra 39mm means thats how much further the new wheels will stick further out, in reference to the original wheels.

[g_mac530]

Originally Posted by fliprayzin240sx

Personally, I would have looked for 70mm in the rear just to be safe. You can't really just throw a random number out there and say well they should bow out 50mm more. All depends on how thick the fiberglass is and what the actual measurements of the fender really are. Just cuz they said 50mm, doesnt mean its exactly 50mm.

Also, which Chargespeed fenders?

Picked up the s14 chargespeeds from Ray (frizzle). And I see what your saying. FG is FG and no one mold is going to be 100% identical. I won't be heart broken if the wheels don't fit. I'm really just looking for a lip which could also be achieved with a negative offset 11 or 12 as well.

[fliprayzin240sx]

Originally Posted by g_mac530

Picked up the s14 chargespeeds from Ray (frizzle). And I see what your saying. FG is FG and no one mold is going to be 100% identical. I won't be heart broken if the wheels don't fit. I'm really just looking for a lip which could also be achieved with a negative offset 11 or 12 as well.

Well, if its chargespeed, then you might be able to flex them more than a US copied fender. JDM kit companies usually lay their fiberglass thin and more flexible than the US ones.

I say, get the wheels you want on, cut the stock fenders, get them seam welded, test fit the fenders with the wheels on so you can see if you'd have to run some camber. Depending on how far out the tires stick will be dependent on how much camber you'd need and how much you'd have to bow out the fenders. Finding that happy medium between bowing the fender and getting your alignment dialed in is where it gets tricky. In an ideal world, you get your alignment done and then get your fenders to fit your setup (wheels/camber).

[delado]

Trying to order some tires for my kouki at the moment but I'm in a bit of a pickle.

Rears are 18x10.5 +22

Fronts are 18X9.5 +12

I'm on Stance GR+

Ideally I would want to run a 225/40 up front and a 265/35 in the rear. (Achilles ATR Sport)

My overall goal is to run minimum camber in the rear. I don't mind running lots of camber in the front. I would also like to keep my metal virgin. I don't mind rolling the lip in but I would like to avoid a pull. I know I won't have issues in the front. But the rear does concern me. What do you fellas think?

[KA-Life86]

Originally Posted by delado

Trying to order some tires for my kouki at the moment but I'm in a bit of a pickle.

Rears are 18x10.5 +22

Fronts are 18X9.5 +12

I'm on Stance GR+

Ideally I would want to run a 225/40 up front and a 265/35 in the rear. (Achilles ATR Sport)

My overall goal is to run minimum camber in the rear. I don't mind running lots of camber in the front. I would also like to keep my metal virgin. I don't mind rolling the lip in but I would like to avoid a pull. I know I won't have issues in the front. But the rear does concern me. What do you fellas think?

I have 18x10 +22 w 265/35 on my s14, they fit with a flat roll and -2.8* camber

[xsephish]

Would
17x9 +12 offset fronts
17x9.5 +12 offset rears
fit on stock metal with just a good roll possibly slight pull or raise the car some?
I have stance gr + pro coils spl rucas
also what ideal tire size on this? I don't want a stretch i want as much tire as i can fit while not throwing the speedo off much if any.

[CharCharXD]

What do I have to do to make 18x9 +35 & 18x10.5 +20 fit s14 kouki?

[CharCharXD]

What do I have to do to make 18x9 +35 & 18x10.5 +20 fit s14 kouki? I have dmax coils. What would be the best tires for a big stretch. How big of spacers? I was also thinking about a square setup 18x10.5 +20 all around? Which would you do?

[vipergtsr1000hp]

Originally Posted by CharCharXD

What do I have to do to make 18x9 +35 & 18x10.5 +20 fit s14 kouki? I have dmax coils. What would be the best tires for a big stretch. How big of spacers? I was also thinking about a square setup 18x10.5 +20 all around? Which would you do?

225/40/18 fronts mild stretch
255/35/18 rears mild stretch

or

215/35/18 fronts bigger stretch
225/40/18 rears big stretch

u would prob need a 20-25mm spacer to clear coils up front.
rears are fine with just a roll.

hope this helps

[Aurox]

Hello everybody! I've searched but I'm still confused about one spec of the future wheels for my DD S13.

The car is and will stay stock arched, but I'll roll and pull the fenders for sure; here in Italy we do have some sick laws about car mods so I'll be forced to run just one tyre size (F&R) that could be 215/45 R17 or 215/40 (actually I could also go for a 225 but would kill the car performance as the S13 have a CA18DET with around 220 HP).

So here's the real question: will 17x9 +25 (like Rota Grids) fit with coilovers and a low ride? And if yes how much camber will be needed ? Don't want to use too much due the nature of the car that's daily driven
Some people says yes and some don't without a tiny spacer.

Here's some useful infos:
_I'm planning to increase the steering angle (usual stuff spacer,tie rods etc)
_I can't go 5 lugs or use spacers (yep it's considered illegal )
_Here in europe Rota wheels with 9J and 4x114.3 is only sold with +25 offset and not +12 or +15 like in the USA

Many thanks for the help
Cheers

[zooopreme]

Originally Posted by Aurox

The car is and will stay stock arched, but I'll roll and pull the fenders for sure; here in Italy we do have some sick laws about car mods so I'll be forced to run just one tyre size (F&R) that could be 215/45 R17 or 215/40 (actually I could also go for a 225 but would kill the car performance as the S13 have a CA18DET with around 220 HP).

So here's the real question: will 17x9 +25 (like Rota Grids) fit with coilovers and a low ride? And if yes how much camber will be needed ? Don't want to use too much due the nature of the car that's daily driven
Some people says yes and some don't without a tiny spacer.

Here's some useful infos:
_I'm planning to increase the steering angle (usual stuff spacer,tie rods etc)
_I can't go 5 lugs or use spacers (yep it's considered illegal )
_Here in europe Rota wheels with 9J and 4x114.3 is only sold with +25 offset and not +12 or +15 like in the USA

Many thanks for the help
Cheers

For the record, 225/40 won't kill your performance, it allows for less stretch for your wheels which means more tire and depending on the tire, it will be beneficial for grip.

Anyway, based on the conditions you pointed out...it won't be exactly "flush" but since you can't use spacers, I would just go with 215/45. As for camber, keep it simple: negative 2-2.5* (at most) will do you fine especially if you want to keep your fenders at a slight roll.

[ME GUSTA]

Probably need a spacer up front to clear coilovers (10-12mm), rears should fit if you roll fenders flat, and ran some decent camber.

i'm new to the 240 platform, so someone with more experience correct me.

I have a square setup 17x9.75 +25 all around with a 10mm spacer up front (effective +15 offset) with a 225 tire and it fits under the front fender with no work.

[B92PPEARL240]

New to the forum and have searched for awhile trying to find an answer to my ?. This post seems to be the most friendly with tire/rim/offset ?'s. I drag the car only no drifting or road racing, just highway runs and 1320's. It has coilovers rear is high up as they go, so I'm not slammed or anything.

Wanting to run xxr521 16x8 in the rear w/ +20 offset w/ a 255/50r16 mickey thompson
rolled fenders not pulled. Will this work without pulling the fenders or any drastic changes?

89 Hatch

[fliprayzin240sx]

^^^Should work...What coilovers are you running?

[B92PPEARL240]

isis coilovers not great but they ride ok and back adjust soft enough to get somewhat good launces out of it. I have about 15 grand tied up in the car (drivetrain, electronic)so suspension was getting circuit sport, isis and budget minded parts

[stihlayota]

heres my stupid question, ive googled n searched on here. i keep finding diff answers so i really dk for sure. i have a 5 lug swapped s13, what is the hub bore size?ive found like 62mm n then 72mm then 66mm.. im ordering hubcentric spacers and dont want to get the wrong ones, thanks!

[zooopreme]

Originally Posted by stihlayota

heres my stupid question, ive googled n searched on here. i keep finding diff answers so i really dk for sure. i have a 5 lug swapped s13, what is the hub bore size?ive found like 62mm n then 72mm then 66mm.. im ordering hubcentric spacers and dont want to get the wrong ones, thanks!

66.1 msglngth

[stihlayota]

thank u sir

[Wyfe]

can somebody give me good instructions on how to pull fenders to look somewhat like ezza's white S14 up there? i'm not looking to make it perfect, i just want a decent looking pull/flare so i can fit my wheels. the quarter's lips are already rolled. it's on my s13, i can post pictures later, but basically every s13 coupe's rear quarters are the same.

[amfh403]

Can someone tell me if Weds Mid Disk clears Z32 front brakes? I'm going to purchase a set of wheels and i don't really want to go with the Hi Disk as i want lip. Thanks in advance.

[yokotas13]

Originally Posted by amfh403

Can someone tell me if Weds Mid Disk clears Z32 front brakes? I'm going to purchase a set of wheels and i don't really want to go with the Hi Disk as i want lip. Thanks in advance.

pretty fucking sure it does

if not its only like 2 or 3mm short of it

[fliprayzin240sx]

^^^More than likely not.

Ezza, Your best bet is to cut the inner off the outter fender so you can pull the upper out some more. Then push the inner up and reweld them back up to the outter to support it back up.

Basically the same shit that Knoop did to his S14.
http://knoop.sumospeed.com/?p=694