Zenki's Unite - Page 776 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

ese 14 · 01-20-2012, 07:42 AM

Quote:

Originally Posted by rebornz

i have a extra navan ill sell for $800 =P

its been snowing a lot here so i actually got some stuff done on my car.
nutted up and pulled my rear fenders. went a bit crazy and had to add spacers lol. ill take better pictures when the car is drivable again

how did you pull them to get it to look like that ?? looks tight

chinabean · 01-20-2012, 07:57 AM

beni alway...i think i heart you and your zenki.

95KA-Turbo · 01-20-2012, 08:21 AM

Quote:

Originally Posted by ese 14

how did you pull them to get it to look like that ?? looks tight

That's what it looks like if you use a fender roller, heat everything up a shit ton, not change the angle on the head of the roller, and do it slowly.

rebornz · 01-20-2012, 08:24 AM

Quote:

Originally Posted by 95KA-Turbo

That's what it looks like if you use a fender roller, heat everything up a shit ton, not change the angle on the head of the roller, and do it slowly.

actually i did change the angle. but i had both angles marked on the roller to make sure both fenders were even. but yeah it was like 30degrees outside so it took me 4 hours to do it lol. i just heated up the whooooole quarter pannel thats all. i roll fenders for beer money so ive gotten pretty good at it

Victory!! · 01-20-2012, 10:21 AM

Irresistible · 01-20-2012, 10:30 AM

Quote:

Originally Posted by rebornz

actually i did change the angle. but i had both angles marked on the roller to make sure both fenders were even. but yeah it was like 30degrees outside so it took me 4 hours to do it lol. i just heated up the whooooole quarter pannel thats all. i roll fenders for beer money so ive gotten pretty good at it

Damn. Wish you lived by me. I'd buy you some beer to have you pull my quarters haha.

lflkajfj12123 · 01-20-2012, 10:58 AM

Quote:

Originally Posted by kalypso123

much better <3

oh shit my j boner is ragin

tricky_ab · 01-20-2012, 11:48 AM

HAHA Co-signed!

ese 14 · 01-20-2012, 11:56 AM

Quote:

Originally Posted by rebornz

actually i did change the angle. but i had both angles marked on the roller to make sure both fenders were even. but yeah it was like 30degrees outside so it took me 4 hours to do it lol. i just heated up the whooooole quarter pannel thats all. i roll fenders for beer money so ive gotten pretty good at it

haha nice im dying for my fenders to look like that, from where did you order your fender roller ?

s14fbs · 01-20-2012, 12:57 PM

Quote:

Originally Posted by ese 14

haha nice im dying for my fenders to look like that, from where did you order your fender roller ?

POWERED BY MAX:

Fender Roller Tool, Fender Rolling Tool For Sale With How To & DIY Instructions

Hardware - Fender Roller

google works wonders use it sometimes

*ManoNegra* · 01-20-2012, 01:00 PM

Quote:

Originally Posted by rebornz

god I hope you had a jack under that thing

I like your car
makes me, for a brief moment, wish I'd kept the second s14 a zenki

95KA-Turbo · 01-20-2012, 01:24 PM

Quote:

Originally Posted by rebornz

actually i did change the angle. but i had both angles marked on the roller to make sure both fenders were even. but yeah it was like 30degrees outside so it took me 4 hours to do it lol. i just heated up the whooooole quarter pannel thats all. i roll fenders for beer money so ive gotten pretty good at it

Nice, that's how I paid for a lot of my car build, LOL. That's a super good pull!

illvialuver · 01-20-2012, 02:04 PM

800 for navan front? that is a great deal, especially if it is paint matched and shipped to South Africa.

chinabean · 01-20-2012, 02:20 PM

Quote:

Originally Posted by illvialuver

800 for navan front? that is a great deal, especially if it is paint matched and shipped to South Africa.

You better scoop that deal up before someone else does - at this great of a deal it'll be gone quick!

kalypso123 · 01-20-2012, 02:49 PM

how does he do the lights...

*fliprayzin240sx* · 01-20-2012, 02:57 PM

Quote:

Originally Posted by s14fbs

POWERED BY MAX:

Fender Roller Tool, Fender Rolling Tool For Sale With How To & DIY Instructions

Hardware - Fender Roller

google works wonders use it sometimes

Eh, dont waste your money on the eastwood one. If you're car is low, its a pain in the ass to use since the arm is too long. I have one and I wish I spent the money on another brand. Then again, PBM and Stance rollers didnt come out till way after I bought my roller. Had this POS for over 6 yrs now.

1on1 · 01-20-2012, 03:05 PM

Quote:

Originally Posted by ManoNegra

god I hope you had a jack under that thing

this. Plus, the jack he has has one-wheel in the front, and they tend tip over when it's not straight.

Overall, I like the car.

Irresistible · 01-20-2012, 03:09 PM

Quote:

Originally Posted by fliprayzin240sx

Eh, dont waste your money on the eastwood one. If you're car is low, its a pain in the ass to use since the arm is too long. I have one and I wish I spent the money on another brand. Then again, PBM and Stance rollers didnt come out till way after I bought my roller. Had this POS for over 6 yrs now.

I second this. I had a hard time using the Eastwood I rented out, and ended up just using a hammer... Lol. Then again, I wasn't pulling them, just rolling.

Zenki_516 · 01-20-2012, 03:31 PM

Just finished some ghetto pulling with a pipe last night. RB kit came this morning so I did a quick test fit.

pandapoo503 · 01-20-2012, 03:58 PM

My last Zenki.

Lukasss · 01-20-2012, 04:29 PM

Quote:

Originally Posted by Zenki_516

Just finished some ghetto pulling with a pipe last night. RB kit came this morning so I did a quick test fit.

..

'Merica.

smithrcing17 · 01-20-2012, 05:01 PM

Quote:

Originally Posted by Zenki_516

Just finished some ghetto pulling with a pipe last night.

I didn't know I was on vwvortex, wait..

240drifter1 · 01-20-2012, 05:59 PM

Get some smaller freakin tires

95KA-Turbo · 01-20-2012, 06:52 PM

Quote:

Originally Posted by fliprayzin240sx

Eh, dont waste your money on the eastwood one. If you're car is low, its a pain in the ass to use since the arm is too long. I have one and I wish I spent the money on another brand. Then again, PBM and Stance rollers didnt come out till way after I bought my roller. Had this POS for over 6 yrs now.

Unbolt shock and put a jack under the LCA to at the desired height.

You can also mount the roller arm down lower on the other set of holes the base has, you just don't have as much leverage so it only works for rolling on certain cars.

Irresistible · 01-20-2012, 07:26 PM

Quote:

Originally Posted by Lukasss

..

'Merica.

Quote:

Originally Posted by smithrcing17

I didn't know I was on vwvortex, wait..

What's wrong with using a pipe? If you know how to do it it'll be done right... Did y'all miss the video of the J-land guy with the pink S14 rolling his quarters with a pipe?

Quote:

Originally Posted by 240drifter1

Get some smaller freakin tires

His tires are fine... Not everyone is part of the hellaflush, tires are smaller than rubberbands shit.

Although, I do not like the hood riser things, and the eye lids make me feel like you're saying "I wanna have a kouki but can't afford the conversion so this is the best I can do."

rebornz · 01-20-2012, 07:57 PM

If by jack do you mean jackstands? Im a flat rate guy sO i never use jackstands lol it takes too long. And that jack has 2 wheels up front so its its more stable.

I have pbm roller and its ok. But its no eastwood i like those better. Nothin wrong with pipes or bats either. You just have to know what your doing. Ive even used a broom handle in a pinch lol

Lukasss · 01-20-2012, 08:00 PM

Quote:

Originally Posted by Irresistible

pipe talk

I was saying 'Merica about the rb kitted car.

JKL1031 · 01-20-2012, 08:05 PM

Quote:

Originally Posted by rebornz

If by jack do you mean jackstands? Im a flat rate guy sO i never use jackstands lol it takes too long. And that jack has 2 wheels up front so its its more stable.

I have pbm roller and its ok. But its no eastwood i like those better. Nothin wrong with pipes or bats either. You just have to know what your doing. Ive even used a broom handle in a pinch lol

you work at a shop? the pump or a link can fail ona jack. its just precaution. but thats abad thing to say for someone who works at a shop.

Irresistible · 01-20-2012, 08:12 PM

Quote:

Originally Posted by Lukasss

I was saying 'Merica about the rb kitted car.

Alrighty. Wasn't sure, I thought you meant the pipe thing, so I expressed my opinion on the matter.

Lukasss · 01-20-2012, 08:15 PM

Its cool, for my 2 cents i dont like the look of fenders that flare out like that, so i took a flat crowbar and pulled the metal outward.

It keeps the oem look, and doesnt wave, crack paint, etc.
I fit a 18x9.5 et 0 with 2* camber on the rear without rubbing and tucking like 2mm of rim

01-20-2012, 07:57 AM	#23252
chinabean Zilvia Addict Join Date: Dec 2009 Location: in burning embers Posts: 655 Trader Rating: (3) Feedback Score: 3 reviews	beni alway...i think i heart you and your zenki. __________________ Zenki Love - I spray paint my stock 15" hubs teal and rockillest/supreme/obey stickers on my car.

01-20-2012, 10:21 AM	#23255
Victory!! Zilvia Junkie Join Date: Aug 2006 Location: WISCO Posts: 341 Trader Rating: (3) Feedback Score: 3 reviews

01-20-2012, 11:48 AM	#23258
tricky_ab Post Whore! Join Date: Sep 2008 Location: It's dark, and hell is hot! Posts: 9,414 Trader Rating: (23) Feedback Score: 23 reviews	HAHA Co-signed!

01-20-2012, 02:04 PM	#23263
illvialuver Post Whore! Join Date: Oct 2006 Location: M-A-R-S... MARS BITCHES Age: 41 Posts: 5,065 Trader Rating: (35) Feedback Score: 35 reviews	800 for navan front? that is a great deal, especially if it is paint matched and shipped to South Africa.

01-20-2012, 02:49 PM	#23265
kalypso123 (ノಠ益ಠ)ノ彡 Join Date: Apr 2008 Location: New York, NY Posts: 2,853 Trader Rating: (2) Feedback Score: 2 reviews	how does he do the lights...

01-20-2012, 03:58 PM	#23270
pandapoo503 Leaky Injector Join Date: Jan 2009 Location: Portland, OR Age: 35 Posts: 62 Trader Rating: (0) Feedback Score: 0 reviews	My last Zenki.

01-20-2012, 05:59 PM	#23273
240drifter1 Zilvia FREAK! Join Date: Mar 2007 Location: Knoxville, TN Posts: 1,505 Trader Rating: (1) Feedback Score: 1 reviews	Get some smaller freakin tires

01-20-2012, 07:57 PM	#23276
rebornz Zilvia Member Join Date: Sep 2009 Location: Renton, WA Age: 34 Posts: 197 Trader Rating: (1) Feedback Score: 1 reviews	If by jack do you mean jackstands? Im a flat rate guy sO i never use jackstands lol it takes too long. And that jack has 2 wheels up front so its its more stable. I have pbm roller and its ok. But its no eastwood i like those better. Nothin wrong with pipes or bats either. You just have to know what your doing. Ive even used a broom handle in a pinch lol

01-20-2012, 08:15 PM	#23280
Lukasss Nissanaholic! Join Date: Jul 2010 Location: San Diego Posts: 1,892 Trader Rating: (5) Feedback Score: 5 reviews	Its cool, for my 2 cents i dont like the look of fenders that flare out like that, so i took a flat crowbar and pulled the metal outward. It keeps the oem look, and doesnt wave, crack paint, etc. I fit a 18x9.5 et 0 with 2* camber on the rear without rubbing and tucking like 2mm of rim