Sr20det FAQ

[moses]

This website helped me out a lot. its where i found what ECU i needed to match my harness
http://www.nodrft.com/page.php?id=25

[sblack13]

I have some useful ecu pinouts I found on the net.

This is for a Zenki S14 SR20 Blacktop WC



and this is the Kouki S14 Blacktop and JDM S15 Pinouts (they are basically the same)

[landins13]

resistance between + and - on the coil packs should be 1 ohm
compression on each cylinder should be 1.087 Kpa minimum of 883 kpa and the most that the cylinders can be off by is 98 Kpa.

I was having compression problems so i figured id post that since it was a pain to find.

[Signum Temporis]

checking oil pressure

[wangan_cruiser]

sr redtop and blacktop can use an 89-90 sohc starter. i made a thread
http://www.zilvia.net/f/showthread.p...27#post1910027

[pwrofdrm]

Most SR20DET swaps, even if they're advertised as 'Complete' do not include the SR20DET Motor Mount Brackets as are required to install the engine (duh)

You can use your stock motor mounts, but not your stock motor mount brackets which are bolted to the block.



Also, it is much easier to install the engine with the motor mounts attached to the swap and then put it in the engine bay, rather than just try to line the brackets up while the mounts are in the car.


Even if your oil pan looks good, take it off and bang it out anyway. Or buy the GReddy oil pan or a replica. Even if it doesn't look too bent in, looks may be deceiving.


When wiring your power up to the engine using a battery relocation kit, don't forget about the two power wires in the harness behind the passenger headlight that were hooked up to the stock battery terminal. Obviously you'll need power to the lower harness on the SR swap, but you need power to these two plugs as well.

[DOHC20sr]

thought id add this hope it helps

Basically the list goes Part/Date/Part Number/Special Note
Engine:
Bare engine assembly Jan 1991 - Jan 1994 10102-50F50
Bare engine assembly Jan 1994 - Aug 1996 10102-50F52
Bare engine assembly Aug 1991 - Dec 1998 10102-50FM2
Short block engine assembly Jan 1991 - Dec 1998 10103-50FM0
Cylinder Block and Oil Pan:
Oil jet assembly Jan 1991 - Aug 1993 11560-79E00
Timing chain oil jet Jan 1991 - Dec 1998 13081-53J00
Timing chain oil jet Aug 1993 - Dec 1998 11560-1E000
Rear oil seal Jan 1991 - Dec 1998 12279-18V00, 12279-30P00, 12279-1E000, 12279-53J10, 12279-85Y00, 12279-1N510
Oil pan lower baffle Jan 1991 - Jan 1994 11113-52F00
Oil pan lower baffle Jan 1994 - Dec 1998 11113-65F00
Main bearing cap bolts Jan 1991 - Dec 1998 12293-53J00
Dipstick Jan 1991 - Dec 1998 11140-52F00
Dipstick tube Jan 1991 - Dec 1998 11150-52F00
Crankcase plate baffle Jan 1991 - Dec 1998 11038-53J00
Rear oil seal retainer Jan 1991 - Dec 1998 12297-53J00
Oil pan Jan 1991 - Dec 1998 11110-52F10
Upper oil pan Jan 1991 - Dec 1998 11110-52F01
Upper oil pan baffle Jan 1991 - Dec 1998 11113-53J02
Rear engine plate Jan 1991 - Dec 1998 30411-52F00 Plate between engine and tranny
Rear plate cover Jan 1991 - Dec 1998 30417-52F00 Plate on back of upper oil pan
Valve Cover/Cylinder Head:
Spark plug cover Jan 1991 - Dec 1998 13287-50F01
Spark plug cover bolt Jan 1991 - Dec 1998 01131-40F01
Valve cover nut Jan 1991 - Nov 1992 01217-00181
Valve cover nut Nov 1992 - Jan 1994 01217-00221
Valve cover nut Jan 1994 - Dec 1998 08918-20610
Valve cover washer Jan 1991 - Dec 1998 13268-97E00
Valve cover stud Jan 1991 - Dec 1998 13508-53J00
Valve cover red Jan 1991 - Jan 1994 13264-50F02
Valve cover black Jan 1994 - Dec 1998 13264-50F03
Valve cover gasket Jan 1991 - Dec 1998 13270-52F00
Valve cover spark gasket Jan 1991 - Dec 1998 13271-52F00
Headgasket Jan 1991 - Dec 1998 11044-50F01
Oil cap assembly Jan 1991 - Dec 1998 15255-40F01, 15255-1P101
Cylinder head assembly Jan 1991 - Dec 1998 11040-52F00
PCV Valve Jan 1991 - Dec 1998 11810-79E01
Intake valve seat Jan 1991 - Aug 1996 11098-53J60
Intake valve seat Aug 1996 - Dec 1998 11098-1E765
Exhaust valve seat Jan 1991 - Aug 1996 11099-53J60
Exhaust valve seat Aug 1996 - Dec 1998 11099-53J65
Timing chain Jan 1991 - Dec 1998 13028-53J03
Chain guide slack side Jan 1991 - Sep 1996 13091-53J01, 13091-2J200
Chain guide slack side Sep 1996 - Sep 1997 13091-2J200, 13091-2J201
Chain guide slack side Sep 1997 - Dec 1998 13091-2J201, 13091-2J202
Chain guide tension side Jan 1991 - Oct 1997 13085-53J00, 13085-1N500
Chain guide tension side Oct 1997 - Dec 1998 13085-1N500
Timing chain tensioner Jan 1991 - Dec 1998 13070-2J200, 13070-2J203
Cam sprocket (intake) Jan 1991 - Dec 1998 13024-53J01
Cam sprocket (exhaust) Jan 1991 - Dec 1998 13095-52F00
Camshaft (intake) Jan 1991 - Dec 1998 13020-1E000
Camshaft (exhaust) Jan 1991 - Dec 1998 13020-50F12
Rocker arm Jan 1991 - Dec 1998 13257-53J03
Hydraulic lash adjuster Jan 1991 - Dec 1998 13234-53J01
Rocker shim (T=2.800) Jan 1991 - Dec 1998 13229-53J00
Rocker shim (T=2.825) Jan 1991 - Dec 1998 13229-53J01
Rocker shim (T=2.850) Jan 1991 - Dec 1998 13229-53J02
Rocker shim (T=2.875) Jan 1991 - Dec 1998 13229-53J03
Rocker shim (T=2.900) Jan 1991 - Dec 1998 13229-53J04
Rocker shim (T=2.925) Jan 1991 - Dec 1998 13229-53J05
Rocker shim (T=2.950) Jan 1991 - Dec 1998 13229-53J06
Rocker shim (T=2.975) Jan 1991 - Dec 1998 13229-53J07
Rocker shim (T=3.000) Jan 1991 - Dec 1998 13229-53J08
Rocker shim (T=3.025) Jan 1991 - Dec 1998 13229-53J09
Rocker shim (T=3.050) Jan 1991 - Dec 1998 13229-53J10
Rocker shim (T=3.075) Jan 1991 - Dec 1998 13229-53J11
Rocker shim (T=3.100) Jan 1991 - Dec 1998 13229-53J12
Rocker shim (T=3.125) Jan 1991 - Dec 1998 13229-53J13
Rocker shim (T=3.150) Jan 1991 - Dec 1998 13229-53J14
Rocker shim (T=3.175) Jan 1991 - Dec 1998 13229-53J15
Rocker shim (T=3.200) Jan 1991 - Dec 1998 13229-53J16
Rocker arm guide Jan 1991 - Dec 1998 13218-53J00
Valve spring collet Jan 1991 - Dec 1998 13210-D4200
Valve spring retainer Jan 1991 - Dec 1998 13209-53J00
Valve spring Jan 1991 - Dec 1998 13203-53J00
Valve spring seat Jan 1991 - Dec 1998 13205-53J00
Intake valve oil seal Jan 1991 - Dec 1998 13207-84A00 NDK
Intake valve oil seal Jan 1991 - Dec 1998 13207-D4201 NOK
Intake valve Jan 1991 - Jan 1994 13201-53J00
Intake valve Jan 1994 - Dec 1998 13201-1E700, 13201-1E710
Exhaust valve oil seal Aug 1996 - Dec 1998 13207-53F00 NOK
Exhaust valve oil seal Jan 1991 - Dec 1998 13207-D0111 NDK
Exhaust valve Jan 1991 - Feb 1996 13202-53J01
Exhaust valve Feb 1991 - Dec 1998 13202-53J02
Front Cover:
Oil pump assembly Jan 1991 - Dec 1998 13500-50F00
Front main seal Jan 1991 - Jan 1994 13510-40F00, 13510-53J10 NDK
Front main seal Jan 1994 - Aug 1996 13510-53J00 NDK
Front main seal Aug 1996 - Dec 1998 13510-53J01 NOK
Front main seal Jan 1991 - Aug 1996 13510-53J10, 13510-53J11 NOK
Front main seal Aug 1996 - Dec 1998 13510-53J11 NDK
Oil pump gear set Jan 1991 - Dec 1998 15020-50F00, 15020-79E00
Oil pump regulator valve set Jan 1991 - Dec 1998 15132-50F00
Engine and Tranny Mount:
Engine mount right Jan 1991 - Apr 1991 11210-40F00
Engine mount right Apr 1991 - Dec 1998 11210-52F00, 11210-65F11
Engine mount left Jan 1991 - Apr 1991 11220-40F00
Engine mount left Apr 1991 - Dec 1998 11220-52F00, 11220-65F06, 11220-85F00
Tranny mount Jan 1991 - Dec 1998 11320-35F01
Tranny crossmember Jan 1991 - Dec 1998 11340-35F00
Engine - Bottom End:
Piston ring set (standard) Jan 1991 - Dec 1998 12033-53J00, 12033-53J01
Piston ring set (0.20 oversize) Jan 1991 - Dec 1998 12035-53J00
Crank Sprocket Jan 1991 - Dec 1998 13021-53J00
Crankshaft assembly Jan 1991 - Dec 1998 12200-60J10
Piston with pin (standard-1) Jan 1991 - Jul 1993 A2010-79E60
Piston with pin (standard-2) Jan 1991 - Jul 1993 A2010-79E61
Piston with pin (standard-3) Jan 1991 - Jul 1993 A2010-79E62
Piston with pin (0.20 oversize) Jan 1991 - Jul 1993 A2010-79E71
Piston with pin (standard-1) Jul 1993 - Dec 1998 A2010-54C00, A2010-75F60
Piston with pin (standard-2) Jul 1993 - Dec 1998 A2010-54C01, A2010-75F61
Piston with pin (standard-3) Jul 1993 - Dec 1998 A2010-54C02, A2010-75F62
Piston with pin (0.20 oversize) Jul 1993 - Dec 1998 A2010-54C10, A2010-75F76
Connecting rod assembly Jan 1991 - Dec 1998 12100-79E00
Con rod bearing (standard-0) Aug 1996 - Dec 1998 12111-1N500
Con rod bearing (standard-1) Aug 1996 - Dec 1998 12111-1N501
Con rod bearing (standard-2) Aug 1996 - Dec 1998 12111-1N502
Con rod bearing (standard-0) Jan 1991 - Aug 1996 12111-60J00, 12111-1N500
Con rod bearing (standard-1) Jan 1991 - Aug 1996 12111-60J01, 12111-1N501
Con rod bearing (standard-2) Jan 1991 - Aug 1996 12111-60J02, 12111-1N502
Con rod bearing (US 0.12) Aug 1996 - Dec 1998 12117-1N500
Con rod bearing (US 0.12) Jan 1991 - Aug 1996 12117-60J00
Con rod bearing (US 0.25) Aug 1996 - Dec 1998 12118-1N500
Con rod bearing (US 0.25) Jan 1991 - Aug 1996 12118-60J00, 12118-1N500
Con rod bearing (US 0.8) Aug 1996 - Dec 1998 12122-1N500
Con rod bearing (US 0.8) Jan 1991 - Aug 1996 12122-60J00
Crank bearing (standard-0) Jan 1991 - Dec 1998 12207-60J00
Crank bearing (standard-1) Jan 1991 - Dec 1998 12207-60J01
Crank bearing (standard-2) Jan 1991 - Dec 1998 12207-60J02
Crank bearing (standard-3) Jan 1991 - Dec 1998 12207-60J03
Crank bearing (standard-4) Jan 1991 - Dec 1998 12207-60J04
Crank bearing (standard-5) Jan 1991 - Dec 1998 12207-60J05
Crank bearing (standard-6) Jan 1991 - Dec 1998 12207-60J06
Crank bearing set (US 0.25) Jan 1991 - Dec 1998 12208-60J00
Thrust washer Jan 1991 - Dec 1998 12280-60J00
Crankshaft pulley Jan 1991 - Dec 1998 12303-52F00
Crankshaft pulley bolt Jan 1991 - Dec 1998 12309-29S00
Clutch:
Flywheel assembly Jan 1991 - Dec 1998 12310-79E11, 12310-79E12
Flywheel bolt Jan 1991 - Dec 1998 12315-52F00
Pilot bushing Jan 1991 - Dec 1998 32202-B9500
Intake/Exhaust Manifold:
Upper intake manifold Jan 1991 - Dec 1998 14001-52F00 Connects to head
Lower intake manifold collector Jan 1991 - Dec 1998 14010-52F00 Connects to throttle body
Throttle body gasket Jan 1991 - Mar 1993 16175-53J00
Throttle body gasket Mar 1993 - Dec 1998 16175-79S70, 16175-79S71
Intake manifold gasket to head Jan 1991 - Dec 1998 14035-53J10
Intake manifold middle gasket Jan 1991 - Dec 1998 14032-52F00
Throttle cable bracket Jan 1991 - Dec 1998 16165-52F00
Throttle cable insulator Jan 1991 - Dec 1998 18316-52F00
Throttle body Jan 1991 - Dec 1998 16118-52F00, 16118-52F05
Throttle position sensor Jan 1991 - Jun 1997 22620-53J00, 22620-53J01
Throttle position sensor Jun 1997 - Dec 1998 22620-31U01
Throttle cable pulley Jan 1991 - Dec 1998 16134-52F00
Idle air control valve Jan 1991 - Dec 1998 23781-50F05 Tousoku
Idle air control valve Jan 1991 - Dec 1998 23781-50F15 Atsugi
Idle air control valve gasket Jan 1991 - Dec 1998 23785-50F00
Exhaust manifold gasket Jan 1991 - Dec 1998 14036-53J00
Exhaust manifold Jan 1991 - Dec 1998 14004-50F00
Exhaust manifold stud Jan 1991 - Aug 1996 08267-03010
Exhaust manifold stud Aug 1996 - Jun 1997 14065-75F00
Exhaust manifold stud Jun 1997 - Dec 1998 14064-2J200
Exhaust manifold washer Jan 1991 - Dec 1998 14037-42L02
Exhaust manifold nut Jan 1991 - Dec 1998 08912-8401A
Turbocharger:
Turbocharger Jan 1991 - Dec 1998 14411-50F00
Manifold to turbo gasket Jan 1991 - Dec 1998 14415-17M00
Turbo to O2 pipe gasket Jan 1991 - Dec 1998 14445-26E00
O2 extension Jan 1991 - Dec 1998 14440-50F01
Locking washer plate Jan 1991 - Dec 1998 14495-17F00
Oil return tube Jan 1991 - Dec 1998 15197-50F00
Oil return gasket Jan 1991 - Dec 1998 15196-79E00
Lubricating System:
Oil filter bracket assembly Jan 1991 - Dec 1998 15238-52F01
Oil pickup tube/strainer Jan 1991 - Sep 1993 15050-52F00, 15050-52F01
Oil pickup tube/strainer Sep 1993 - Dec 1998 15050-65F01
Oil pickup O-ring seal Jan 1991 - Jan 1994 15059-V5001
Oil pickup O-ring seal Jan 1994 - Dec 1998 15053-1E400
Cooling:
Waterpump Jan 1991 - Dec 1998 21010-52F01
Waterpump pulley Jan 1991 - Dec 1998 21051-65F00
Clutch fan clutch Jan 1991 - Dec 1998 21082-52F00
Clutch fan fan Jan 1991 - Dec 1998 21060-52F00
Upper waterneck Jan 1991 - Aug 1996 11060-52F00, 11060-52F01
Upper waterneck Aug 1996 - Dec 1998 11060-65F00, 11060-65F01
Lower water inlet Jan 1991 - Dec 1998 13049-52F00
Thermostat Jan 1991 - Dec 1998 21200-53J00, 21200-53J10, 21200-0C810
Thermostat housing Jan 1991 - Dec 1998 11061-52F05
Engine coolant temp sensor Jan 1991 - Jan 1994 22630-V5010, 22630-51E00
Engine coolant temp sensor Jan 1994 - Aug 1996 22630-51E00, 22630-51E02
Engine coolant temp sensor Aug 1996 - Dec 1998 22630-43Y00, 22630-44B10
Engine coolant temp sensor Aug 1996 - Oct 1997 22630-44B10, 22630-44B20
Engine coolant temp sensor Oct 1997 - Dec 1998 22630-44B20
Radiator Jan 1991 - Dec 1998 21410-52F11
Resevoir tank Jan 1991 - Dec 1998 21721-35F01
Upper radiator shroud Jan 1991 - Dec 1998 21476-52F00
Lower radiator shroud Jan 1991 - Dec 1998 21477-35F00
Fuel system:
Fuel injector Jan 1991 - Dec 1998 16600-50F00, 16600-50F02, 16600-50F10, 16600-50F12
Small injector O-ring Jan 1991 - Dec 1998 16618-53J00
Large injector O-ring Jan 1991 - Dec 1998 16618-10V05
Injector insulator Jan 1991 - Dec 1998 16635-53J00
Injector rubber back cap Jan 1991 - Dec 1998 16619-53J00
Fuel rail Jan 1991 - Dec 1998 17520-52F00
Fuel pressure regulator Jan 1991 - Dec 1998 22670-52F00
Fuel pump Jan 1991 - May 1991 17042-35F00
Fuel pump May 1991 - Dec 1998 17042-73L02
Intake:
Mass air flow sensor Jan 1991 - Dec 1998 22680-52F00
Compressor inlet tube Jan 1991 - Dec 1998 16577-50F00 bolts to turbo
Compressor inlet tube gasket Jan 1991 - Dec 1998 14465-54C00
Intake rubber tube Jan 1991 - Dec 1998 16578-50F01
Ignition System:
Coilpack Jan 1991 - Dec 1998 22448-50F01
Coilpack harness Jan 1991 - Dec 1998 24079-50F00
Igniter chip (PTU) Jan 1991 - Dec 1998 22020-50F00, 22020-50F01, 22020-50F10
Knock sensor Jan 1991 - Dec 1998 22060-30P00
Camshaft position sensor (CAS) Jan 1991 - Dec 1998 23731-50F02
Electronics:
Wastegate control solenoid Jan 1991 - Dec 1998 14956-50F00
Oxygen sensor Jan 1991 - Jan 1994 22690-50F00
Oxygen sensor Jan 1994 - Dec 1998 22690-50F02
Oxygen sensor holding nut Jan 1991 - Jan 1994 20607-V5000
Oxygen sensor holding nut Jan 1994 - Dec 1998 20607-P6500
ECU Jan 1991 - Jan 1994 23710-50F00 MT
ECU Jan 1994 - Aug 1996 23710-50F05 MT
ECU Jan 1991 - Jan 1994 23710-50F10 AT
ECU Jan 1994 - Aug 1996 23710-50F15 AT
ECU Aug 1996 - May 1997 23710-60F06 MT
ECU May 1997 - Dec 1998 23710-60F07 MT
ECU Aug 1996 - May 1997 23710-60F16 AT
ECU May 1997 - Dec 1998 23710-60F17 AT
Alternator Jan 1991 - Aug 1996 23100-52F10, 23100-52F11
Alternator Aug 1996 - Dec 1998 23100-65F17
Starter Jan 1991 - Dec 1998 23300-52F01, 23300-80F00
Tachometer gauge Jan 1991 - Jan 1994 24825-52F00
Tachometer gauge Jan 1994 - Aug 1996 24825-52F20
Temperature sensor Jan 1991 - Aug 1996 25080-89903
Temperature sensor Aug 1996 - Dec 1998 25080-89907
Power Steering:
Power steering pump Jan 1991 - Dec 1998 49110-52F00 2WS
Power steering pump Jan 1991 - Dec 1998 49110-52F60 4WS Hicas
Transmission:
Clutch slave cylinder Jan 1991 - Mar 1997 30620-18V01, 30620-69F01, 30620-69F02, 30620-69F03
Clutch slave cylinder Mar 1997 - Dec 1998 30620-0H620
SR20DET transmission Jan 1991 - Aug 1996 32010-50F00, 32010-50F20, 32010-50F21, 32010-50F22
SR20DET transmission Aug 1996 - Dec 1998 32010-69F10
SR20DET front belhousing shell Jan 1991 - Apr 1995 32101-50F00
SR20DET front belhousing shell Apr 1995 - Dec 1998 32101-50F01
Speed sensor assembly Jan 1991 - Aug 1996 25010-35F00 Same as US S13
Speed sensor assembly Aug 1996 - Dec 1998 25010-71T00
Speed sensor pinion gear Jan 1991 - Aug 1996 32743-35F20
Speed sensor pinion gear Aug 1996 - Dec 1998 32743-71T20
Driveline/Suspension:
Output flange (right 5 star) Jan 1991 - Oct 1995 38220-53F00, 38220-93L00
Output flange (right 6 bolt) Oct 1995 - Dec 1998 38220-92L00
Output flange (left 5 star) Jan 1991 - Oct 1995 38220-53F01
Output flange (left 6 bolt) Oct 1995 - Dec 1998 38220-52F01
Half shaft (right 5 star) Jan 1991 - Oct 1995 39600-73L00
Half shaft (right 6 bolt) Oct 1995 - Dec 1998 39600-35F00
Half shaft (left 5 star) Jan 1991 - Oct 1995 39601-73L00
Half shaft (left 6 bolt) Oct 1995 - Dec 1998 39601-35F10
Front strut tower bar Dec 1995 - Aug 1996 E4390-50F00
Front strut tower bar Aug 1996 - Dec 1998 E4390-60F00
Nismo front strut tower bar Jan 1996 - Aug 1998 E4420-RN521
Rear swaybar Jan 1991 - Dec 1998 56230-39F03 Other Desired JDM 180SX Parts:
Digital climate control Jan 1991 - Aug 1996 27510-52F00
Digital climate control Aug 1996 - Dec 1998 27510-60F01
Digital control subharness Jan 1991 - Aug 1996 24042-52F00
Resister for climate control Jan 1991 - Jan 1994 27150-51E01
Resister for climate control Jan 1994 - Aug 1996 27150-51E05
Cabin temp sensor Jan 1991 - Dec 1998 27720-35F03
Sunload sensor Jan 1991 - Dec 1998 27721-35F00
Kouki front bumper cover Aug 1996 - Dec 1998 F2022-60F** **varies by color
Kouki optional lip spoiler Aug 1996 - Dec 1998 K6010-60F50
Kouki fender side piece (left) Aug 1996 - Dec 1998 62025-60F**
Kouki fender side piece (right) Aug 1996 - Dec 1998 62024-60F**
Chuki side skirt (left) Dec 1995 - Aug 1996 76851-51F81, 76851-51F25
Chuki side skirt (right) Dec 1995 - Aug 1996 76850-51F81, 76850-51F25
Side skirt #2 (kit) Jan 1991 - Aug 1996 G6850-40F**
Side skirt #2 (left) Jan 1991 - Aug 1996 G6852-40F10
Side skirt #2 (right) Jan 1991 - Aug 1996 G6851-40F10
Kouki side skirt kit #2 Aug 1996 - Dec 1998 G6850-60F**
Kouki side skirt (front-left) Aug 1996 - Dec 1998 76853-60F**
Kouki side skirt (front-right) Aug 1996 - Dec 1998 76852-60F**
Kouki side skrit (rear-left) Aug 1996 - Dec 1998 76857-60F**
Kouki side skirt (rear-right) Aug 1996 - Dec 1998 76856-60F**
Kouki rear spoiler Aug 1996 - Dec 1998 K6030-60F25, K6030-60F26
Kouki rear valence kit Aug 1996 - Dec 1998 H5910-60F**
Rear valence kit Jan 1991 - Aug 1996 H5910-51F**
Rear valence (left) Jan 1991 - Aug 1996 H5913-51F10
Rear valence (middle) Jan 1991 - Aug 1996 H5911-51F10
Rear valence (right) Jan 1991 - Aug 1996 H5912-51F10
180SX side glass (right) Jan 1991 - Jan 1995 83300-47F00
180SX side glass (right) Jan 1995 - Dec 1998 83300-47F01
180SX side glass (right) Sep 1997 - Dec 1998 83300-47F02
180SX side glass (left) Jan 1991 - Jan 1995 83301-47F00
180SX side glass (left) Jan 1995 - Dec 1998 83301-47F01
180SX side glass (left) Sep 1997 - Dec 1998 83301-47F02
180SX Rain guards Jan 1991 - Dec 1998 G3810-40F00
Kouki front seat (back assy) Aug 1996 - Dec 1998 87600-60F00 Both sides
Kouki front seat (cushion assy) Aug 1996 - Dec 1998 87300-60F00 Right side
Kouki front seat (headrest) Aug 1996 - Dec 1998 86400-80F10 Both sides
Kouki front seat (cushion assy) Aug 1996 - Dec 1998 87350-60F00 Left side
Kouki rear seat (back assy) Aug 1996 - Dec 1998 88600-60F00
Kouki rear seat (cushion assy) Aug 1996 - Dec 1998 88300-60F00
180SX Key (with 180SX logo) Jan 1991 - Dec 1998 KEY00-00135
Zenki front turn signal (right) Mar 1989 - Jan 1991 B6120-44F00
Zenki front turn signal (left) Mar 1989 - Jan 1991 B6125-44F00
Chuki front turn signal (right) Jan 1991 - Aug 1996 B6120-50F00
Chuki front turn signal (left) Jan 1991 - Aug 1996 B6125-50F00
Kouki front turn signal (right) Aug 1996 - Dec 1998 B6130-60F00
Kouki front turn signal (left) Aug 1996 - Dec 1998 B6135-60F00
Front amber sidemarker (right) Mar 1989 - Dec 1998 26160-47F00
Front amber sidemarker (left) Mat 1989 - Dec 1998 26165-47F00
Kouki parking light (right) Aug 1996 - Dec 1998 B6170-60F00
Kouki parking light (left) Aug 1996 - Dec 1998 B6175-60F00
180SX rear center light Mar 1989 - Aug 1996 26540-47F00
Kouki tail light (right) Aug 1996 - Dec 1998 B6550-60F00
Kouki tail light (left) Aug 1996 - Dec 1998 B6555-60F00
Kouki tail light (center) Aug 1996 - Dec 1998 26540-60F**
Kouki tail center (carbon?) Aug 1996 - Dec 1998 K0810-60F00
Kouki rear trim panal Aug 1996 - Dec 1998 85230-60F00
Navan steering wheel Jan 1991 - May 1995 D840V-11100
Navan steering wheel (Hicas) Jan 1991 - May 1995 D840V-11130
Momo steering wheel Aug 1996 - Dec 1998 D8400-C9901

[DDDsquad_s13panda]

DIDNT SEE NO FAQ's ABOUT THE N/A SR's, So here my share of a couple things:

Distributor rotor : nissan 200NX
Distributor cap: DOHC KA(must be mitsubishi equip) SE-R AND G20 caps wont work.
AND due to the direction of the port's you'll need the DOHC KA sparkplug wires
RWD-SR20DET/DE clutch are identical
DOHC KA PS can fit to SR20DE/DET , but you have to swap the tension bracket and pulleys

thats all i came across so far with my N/A SR.

[Z33dori]

Block Dowels are the same for all SR20s ... not sure if its been mentioned.

part number
11053-01M00

[usdm180sx]

Nissan has a part number for spark plugs. They are NGK 7 cold rating copper spark plugs. The part number is 22401-20J07. They come gapped at .35 so they need to be regapped to .28. Why does this matter? Because these plugs only cost $2.90 each.

[nismoninjagtr]

1999 honda civic si ngk v-power spark plugs work in the rwd SR20DET

[S14chicka]

Anyone wanna explain the difference between a s13 sr20det blacktop and the s14 sr20 blacktop?

[Damnthats13]

This is my problem, I installed an aftermarket turbo manifold (Megan) and a aftermarket intake manifold (Freddy). My car cranks up and starts to idle back and forth from high to low then about 10 seconds it will cut off. I have no clue where to begin looking at. Can somebody lend me some help with this issue, thanks.

[rb25_s13*CHUKI]

Fuckin love sr20, Kas are weaaaaaaaaak

[initial240sx]

hi, i need some advices, i want to buy the full gasket kit from Cometic... now, this kit comes with A HG 87.5x1.2mm, and the OEM is 86mm bore size... this 1.5mm gap is confusing me... too risky or it doesnt going to affect? should i buy it or find another HG size?

S13 SR20DET RedTop T25 7-12psi

[usdm180sx]

Originally Posted by initial240sx

hi, i need some advices, i want to buy the full gasket kit from Cometic... now, this kit comes with A HG 87.5x1.2mm, and the OEM is 86mm bore size... this 1.5mm gap is confusing me... too risky or it doesnt going to affect? should i buy it or find another HG size?

S13 SR20DET RedTop T25 7-12psi

Cometic is junk get an Apex hg

[ka24depaul]

SR20det Red top or Black top?? Whats the difference??(Besides the years of the engines.).

[JDMxJosh]

Originally Posted by ka24depaul

sr20det red top or black top?? Whats the difference??(besides the years of the engines.).

read previous posts -___-;

[brudacille]

Originally Posted by JDMxJosh

read previous posts -___-;

+100 for u

[supramon808]

Hi sry for being a noob...bought my 1997 kouki with an s13 redtop sr20det swap to it...was reading really hot when the engine was cold..did some research and found out that the people that installed the sr20det didnt swap the temperature sensor for the gauge..bought one for 1997 ka24de (chassis wise) and now its working how it suppose to....now as for the other sensor that goes to the ECU...do i need to swap that too with one from a 1997 KA24de... cuz i read stories of sr20det swaps running rich because of the temp sensor for the ECU...also i saw a writeup of a non turbo SR20de swap..the person who wrote it sed swap both temp sensors..because if u dnt swap the sensor that gives info to the ECU it will run rich..i was wondering if this would apply to my situation or the s13 SR20det...do i need to replace it with one from a 1997 ka24de? also seems like im running rich because car is giving poor gas mileage...

[ultimateirving]

Originally Posted by supramon808

bought one for 1997 ka24de (chassis wise) and now its working how it suppose to....now as for the other sensor that goes to the ECU...do i need to swap that too with one from a 1997 KA24de... cuz i read stories of sr20det swaps running rich because of the temp sensor for the ECU...also i saw a writeup of a non turbo SR20de swap..the person who wrote it sed swap both temp sensors..because if u dnt swap the sensor that gives info to the ECU it will run rich..i was wondering if this would apply to my situation or the s13 SR20det..also seems like im running rich because car is giving poor gas mileage...

it is possible, i used a CTS of a 91 se'r. and it runs beautifully. I didnt even think my sensor was bad, but after swapping it ran much smoother.

[K_style]

Originally Posted by Jeff240sx

Start it. I will delete unnecessary and off topic posts.
This thread should be something along the lines of how hard is the swap, what's required. Power level stages, build ups, cost tally, and power levels. Warnings and things to watch out for during swap, mods.
I figure this will save alot of heartache as noobs can read this thread and not post stupid questions.
-Jeff

I though it was a pretty clear in the beginning..
Please no questions in the thread.

[ShadowMan]

Just throwing this out there. Oil eats rubber, or more specifically any petroleum based products deteriorate rubber based products. Hence water based lubes with your condoms. So to the "know it all's" on here knocking people for dumb questions, then giving crappy advice, take a second and think about when you didnt know shit either. Otherwise, anyone new to working on their car who comes here for help is going to be coming back and asking why this fell apart or that this new hose that they slipped on with a little oil just split 3-6 months later, and you'll have to be annoyed and tell them to go search some obscure post sprinkled with bad advice again.

[ultimateirving]

what is the best plugs for an e85 tune? low psi, around 16psi

[trsebert]

OMFG the next person that asks a question I vote gets banned. I just started reading this thread because I figured it would be full of great information to frequently asked questions, but what did I find? A bunch of noobs asking questions about their own personal problems and questions. STOP FUCKING ASKING QUESTIONS IN HERE AND POST UP ONLY IF YOU HAVE GOOD RELIABLE INFOR-FUCKING-MATION!!!!!!
/rant

Most simple boost leak test (for more minor leaks) spray bottle full of soapy water, spray on IC piping couplers, look for bubbles.

When replacing thermostat, one of the first things that you should change before installing motor, make sure to take the rubber ring off the edge of the t-stat. It won't seat right otherwise, at least in redtop.

AC = easy on the SR. I took KA suction, and high pressure lines, and used the SR compressor fittings that came on the SR compressor (assuming it came with your motor) and took to custom hose maker/fabricator, they welded aluminum SR fittings onto KA lines. Hint: there is a discharge/fill nipple on one of the lines right near the intake inlet on the turbo. when you have the hoses mated, you will want the section with the nipple on it rotated to parallel with the ground, so it doesnt get in the way of the intake tubing(stock). And make sure to replace all o-rings and the accumulator/collection tank.

I've got some more stuff, just got to dig it out of the back of my head.

[IwantAs13]

Im a n00b, but does anyone know or have a picture of a sr-20 labeled. I know what the headers and downpipes n shit like that are, but more of inside the engine block. Also how the engine works. sorry for the lame ass questions, no one in my family knows anything about cars

[khalimadeath]

Originally Posted by IwantAs13

Im a n00b, but does anyone know or have a picture of a sr-20 labeled. I know what the headers and downpipes n shit like that are, but more of inside the engine block. Also how the engine works. sorry for the lame ass questions, no one in my family knows anything about cars

I know its tempting to post a question in a thread dedicated to info only but it makes it much more difficult for someone like me searching for an answer. So if you would read even a page of posts you would see half the posts in this thread are telling dumb-asses like you to search for the info..ITT none the less. Here are some links that have helped me along the way...

SR20DET wiring ECU pins and description of wire colors

Nissan 240sx Performance, Modification, Repair and DIY Articles - by NICOclub.com

.: Ultimate 240SX Guide: ECU Pinout Diagrams :.

[jasonb]

s13 blacktop ecu spits out 0-5v square wave on tach output. i needed that info bad when wiring in my AIM dash which expects 0-12v square. a 47k ohm pullup resistor worked perfect for me. note: i've never tried using a dash other than the AIM so ymmv. If you use a pullup, i would recommend using a switched 12v power so you don't pull current through the ecu 24/7.

[Pommy1705]

Hi guys

Im new to this not sure how to post a new topic, I've just put the blacktop sr20det back into my s14 after a full rebuild, I have no spark at the coils and doesn't sound like the fuel pump is going either?? Any ideas?

[khalimadeath]

Heres a helpful page

http://alarmsellout.com/support/diag...01989-1998.pdf