|
For Sale Items Post items for sale here. ABSOLUTELY NO COMMERCIAL SALES. |
|
Thread Tools | Display Modes |
11-04-2013, 10:42 AM | #1 |
Post Whore!
Join Date: Jun 2009
Location: Pair of dice, Norcal
Age: 34
Posts: 2,621
Trader Rating: (24)
Feedback Score: 24 reviews
|
Lots of good stuff for sale
S14 front seat belts $80 shipped
these S13 control arms are new, they are a bit dirty. I only used them for my car to sit on. Also, the plastic piece that goes on the bottom of the RLCA is rare I believe you can't get them at the dealer anymore? $200 Untitled by d_2jzgte, on Flickr S13 tension rods with Energy bushings $30 Untitled by d_2jzgte, on Flickr Z32 rear cross drilled and slotted rotors basically new, never put miles on it. $70 Untitled by d_2jzgte, on Flickr Ichiba rear hubs, basically new, less than 1 mile on them. a little dirty and I painted it, now the paint is peeling off. $200 Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr wood grain DIN pocket. $20 IMG_3128 by d_2jzgte, on Flickr IMG_3127 by d_2jzgte, on Flickr Z32 aluminum uprights with brand new ball joint spacer and dust shield. I spent $60 alone for the ball joint spacer and dust shield brand new from dealer. $70 for it all Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr used hatch trunk/gas door cable $20 IMG_3158 by d_2jzgte, on Flickr This is a Bolt on swap. STI Brembo Caliper with Braided lines, thick pads, Cross drilled and slotted Evo rotors, brackets, bolts. Clean good working condition calipers. $1000 shipped I need it gone now. I am moving soon and I can use the money. 530 518 5235 IMG_3142 by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr I have a set of Weds Kranze Cerberus 1 in 18x7.5 +40 5x114.3 $800. I can ship at buyers expenses Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr Untitled by d_2jzgte, on Flickr
__________________
REVIEW |
Sponsored Links |
11-04-2013, 01:08 PM | #2 |
Zilvia Member
Join Date: Jun 2009
Location: Psl, Florida
Age: 32
Posts: 161
Trader Rating: (1)
Feedback Score: 1 reviews
|
Would that din cup holder fit into the s13? Looks like there is two parts to that one. I dont know where that top wooden piece would go in a s13.
__________________
I'd walk a thousand miles with a broken spine before i'd change my mind. |
11-04-2013, 07:20 PM | #3 |
Post Whore!
Join Date: Jun 2009
Location: Pair of dice, Norcal
Age: 34
Posts: 2,621
Trader Rating: (24)
Feedback Score: 24 reviews
|
yes it will. In fact, thats in a S13 in the picture above and it could go either way. you can have it on top or bottom, whatever you preffer.
__________________
REVIEW |
11-04-2013, 10:22 PM | #4 |
Nissanaholic!
Join Date: Aug 2013
Location: Denver
Age: 40
Posts: 2,052
Trader Rating: (14)
Feedback Score: 14 reviews
|
You know if the fuel door/ trunk release will work on the coupe/vert?
If so, I'll take it!
__________________
S13 Vert | SR | PE1420 | 5-Speed | 15x9.5 - 0 | |
11-04-2013, 11:28 PM | #6 | ||
Post Whore!
Join Date: Jun 2009
Location: Pair of dice, Norcal
Age: 34
Posts: 2,621
Trader Rating: (24)
Feedback Score: 24 reviews
|
Quote:
No coupe and hatch have different mounting bracket. although, I think I have another one for a coupe. I will check and I will let you know. Quote:
I think your seeing stuff, I don't have a ECU for sale. Lol pm on the way
__________________
REVIEW |
||
Bookmarks |
|
|