The everything cd009 swap thread. - Page 5 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

TheRealSy90 · 08-01-2016, 06:18 PM

Seems like he revised the plate so that you wouldn't have to modify it. Isn't that a good thing?

Sent from my iPhone using Tapatalk

MattTenFour · 08-02-2016, 01:36 AM

Absolutely. I wanted to make sure I wasn't missing something. The instructions that he provided did not reflect any changes to the design and said you have to grind down a portion of the starter. Just trying to iron out the details while the engine and transmission are out of the car and everything is still easy to get to.

Kylepaschke · 08-02-2016, 09:08 AM

Quote:

Originally Posted by RickS14

I would like the input on the cbf.wonder how the throws feel also from left to right. Seems like gktech took a while to release what they offer because they did a fair amount of real world use. Plus the unit looks pretty solid.cbf doesn't seem to have any lower support like serial nine and gktech shifters do. I'm a doing a 2j s14. I'm really thinking about keeping my gktech and just modify the shifter.

Sent from my iPhone using Tapatalk

Its very tight left to right however I haven't driven my car yet

My friend Landon said his was very tight left to right too but once he started driving it really acts normal.

Ill report back once my car is running

RickS14 · 08-02-2016, 09:29 AM

Quote:

Originally Posted by Kylepaschke

Its very tight left to right however I haven't driven my car yet

My friend Landon said his was very tight left to right too but once he started driving it really acts normal.

Ill report back once my car is running

Thanks.

Sent from my iPhone using Tapatalk

Johannes · 08-02-2016, 01:26 PM

Quote:

Originally Posted by RickS14

It's gonna be off. But I think it if you cut the shifter and bend it forward you could get it in stock location under the boot trim and centered. Check out the 2jz swap thread someone has posted pics already. As fas as the gktech one goes.

Sent from my iPhone using Tapatalk

It seems like Nissansota is running thicker JZ-CD adapters than us though. Our Collins adapter is a bit thinner than that and would move the shifter forward. Might still be a tad bit long.

TheRealSy90 · 08-02-2016, 02:36 PM

But his adapter also uses a different bellhousing than the Collins adapter so without a measurement of overall length to compare to its difficult.

Sent from my iPhone using Tapatalk

Nissansota240 · 08-02-2016, 09:30 PM

Here's the measurements on my DL adapter I'm running

And the length from the face of the bell housing to the bolt holes for the shifter

Sent from my SCH-I545 using Tapatalk

RickS14 · 08-02-2016, 09:47 PM

Thank you for that.

Sent from my iPhone using Tapatalk

Johannes · 08-17-2016, 07:07 PM

Just placed an order from a group buy going on @ cbf performance. This shifter is adjustable fore & aft as well as side to side so it fits many application. Orig price is $350. Group buy is $185.

My setup is a 2J ->CD009 with Collins adapter.

Here's the link to his ig page:
https://www.instagram.com/cbfperformance/

Link to group buy:
http://www.cbfperformance.net/store#...egory=19722030

Sent from my SAMSUNG-SM-G935A using Tapatalk

2muchboost · 08-17-2016, 11:19 PM

Almost certain this will work for the LSX setup but can anyone confirm before I place an order?

rbs14kouki · 08-18-2016, 05:51 AM

We just did a cd009 to rb25 in a r32 gts

Collins plate was ruff and no instruction at all . Machined down the bellhousing to accept the plate

Put every thing on the engin to figure out that the starter doesnt fit . Bellhousing need more grinding

With the rb25 kit . The transmission is clocked like 4 or 5 degre (dont know if its an accident by collins) so shifter is tilting toward the driver(rhd) abit

We installed 2 shifter . Firstly the serial nine

We liked it because we could fine tuned our shifter position with our tilted problem ... but shift throw is super short and super easy to miss 3rd or 4th for other gears ...

Second shifter and the one that is staying in GkTech

Shifts are precised and not to short ... realy what i was looking for . Reverse lock out that work 100%

Sit abit more back compare to serial 9 but were gona live with it since its a way better unit to our eyes

NorcalAP2 · 08-18-2016, 11:43 AM

Quote:

Originally Posted by Nissansota240

Got a perfectly working speedo, will do a lil write up later this week .

Sent from my SCH-I545 using Tapatalk

would love to hear how this was done if you used an AEM infinity ECU

RickS14 · 08-18-2016, 01:08 PM

The gktech is a nice piece I sold mine already because I want to keep oem interior. So I'm going with serial nine. Any one have experience with the cbf?

Sent from my iPhone using Tapatalk

TheRealSy90 · 08-18-2016, 03:02 PM

Quote:

Originally Posted by NorcalAP2

would love to hear how this was done if you used an AEM infinity ECU

Same here as I just bought an infinity myself. However I've heard it might be possible that the infinity can convert any speed signal internally and would make the dakota converter no longer needed.

roninwon · 08-18-2016, 09:27 PM

Quote:

Originally Posted by RickS14

The gktech is a nice piece I sold mine already because I want to keep oem interior. So I'm going with serial nine. Any one have experience with the cbf?

Sent from my iPhone using Tapatalk

I thought the gktech required no modifications to the interior. Is that wrong?

TheRealSy90 · 08-18-2016, 09:27 PM

Quote:

Originally Posted by roninwon

I thought the gktech required no modifications to the interior. Is that wrong?

It doesn't. I believe he is running the trans behind a Jz or Ls though. Gktech is designed for Sr.

Sent from my iPhone using Tapatalk

RickS14 · 08-19-2016, 08:34 AM

Right a jz not sr with Collins plate on a s14. It could work but I want to keep it centered as possible and under oem shifter boot.

Sent from my iPhone using Tapatalk

Croustibat · 08-19-2016, 09:20 AM

Quote:

Originally Posted by 2muchboost

So I have searched high and low and have not come up with a clear answer. I know the CD009 can handle some good power but what is the "threshold" for it? I have seen them behind 1krwhp 350z in one video, behind an LSx in another, behind an 2J in another but again no clear indication to the sweet spot before it grenades.

Depends on what you do when you first hear wear signs.

I know of one, fitted to a 500+ Whp rb25 / ps13 . I think it started to whine a bit, after a couple of year of abuse as a pro drifting machine taking part in numerous european championships. It only needs new bearings.

If it can take that kind of abuse (it really IS abused), i cannot see a zilvian user destroy one. Unless it is not correctly installed.

Edit:

quick question here. I do not like plate adapters for various reasons, and am interested in the JWT kit. There is something i don't quite understand though. It requires an automatic bellhousing; but is it a Z33 auto bell housing, or a SR20 auto bellhousing ? Has anyone here installed one ?

Since i am using a CA18DET, i think i am getting in trouble here ...

japslapsilvia · 08-19-2016, 09:52 AM

Quote:

Originally Posted by Croustibat

Edit:

quick question here. I do not like plate adapters for various reasons, and am interested in the JWT kit. There is something i don't quite understand though. It requires an automatic bellhousing; but is it a Z33 auto bell housing, or a SR20 auto bellhousing ? Has anyone here installed one ?

Since i am using a CA18DET, i think i am getting in trouble here ...

Auto Bellhousing from the motor you are adapting to, IE SR- SR Auto Housing. Are the bolt patterns the same for SR/CA?

Nissansota240 · 08-19-2016, 10:57 AM

Quote:

Originally Posted by TheRealSy90

Same here as I just bought an infinity myself. However I've heard it might be possible that the infinity can convert any speed signal internally and would make the dakota converter no longer needed.

I'll see what I can do, I'm super busy lately, might have some time next week.

TheRealSy90 · 08-19-2016, 11:07 AM

Quote:

Originally Posted by Croustibat

quick question here. I do not like plate adapters for various reasons, and am interested in the JWT kit. There is something i don't quite understand though. It requires an automatic bellhousing; but is it a Z33 auto bell housing, or a SR20 auto bellhousing ? Has anyone here installed one ?

Since i am using a CA18DET, i think i am getting in trouble here ...

It uses the auto bellhousing of the engine you have. Idk if they make a kit for the ca18 though.

Sent from my iPhone using Tapatalk

undant · 08-19-2016, 08:52 PM

In to see if anyone can perfect the shifter setup when mated to a JZ motor.

jackal264 · 08-20-2016, 12:30 AM

Quote:

Originally Posted by undant

In to see if anyone can perfect the shifter setup when mated to a JZ motor.

the serial nine cd999 shifter is what you are looking for.

i just picked one up myself. i'll snap a few pictures for you when i get a chance. but my buddy has been running one in his 700hp 2jz s14 for a bit now and its definitely the way to go for 2jz+cd into an s chassis. no cutting of the trans tunnel needed.

retains reverse lockout also.

i know they made a lot on their first production run and they are down to the last hand full already.

https://serialnine.com/contact-info

https://scontent-sea1-1.xx.fbcdn.net...ae&oe=58493A7A

TheRealSy90 · 08-20-2016, 12:32 AM

CBF has a shifter that sits on the inspection plate if you really need it far forward.

Sent from my iPhone using Tapatalk

Johannes · 08-20-2016, 11:09 AM

Everyone checkout my post a couple of posts earlier. Cbf is doing a group buy on any cd009 -> jz/ls/SR to an s-chassis. Pro series utilizes adjustable fore & aft as well as side to side.

Johannes · 08-20-2016, 11:35 AM

Jason's pro series will be similar to the serialnine cd999 shifter setup, except it's a fraction of its cost. $185 group buy of 50 vs $450.

Sent from my SAMSUNG-SM-G935A using Tapatalk

RickS14 · 08-20-2016, 12:54 PM

Quote:

Originally Posted by Johannes

Jason's pro series will be similar to the serialnine cd999 shifter setup, except it's a fraction of its cost. $185 group buy of 50 vs $450.

Sent from my SAMSUNG-SM-G935A using Tapatalk

Waiting to see how the final product will work out.

Sent from my iPhone using Tapatalk

rbs14kouki · 08-20-2016, 08:06 PM

for a jz to cdxxx i would do the speedtek cut and weld bellhousing with the gktech shifter .... with that bellhousing mod you dont need to cut the tunnel ... check them out on Facebook

lsineon · 08-20-2016, 08:43 PM

In to see if anyone can perfect the shifter setup when mated to a JZ motor.

jackal264 · 08-21-2016, 03:22 AM

Quote:

Originally Posted by rbs14kouki

for a jz to cdxxx i would do the speedtek cut and weld bellhousing with the gktech shifter .... with that bellhousing mod you dont need to cut the tunnel ... check them out on Facebook

this looks super janky to me.

the collins kit (the cut + middle plate) looks way better to me then this option. now if collins would get off his ass and make a plate compatible with the j3 housing we would all be golden. seems like everyone has a j3 housing kicking around but the j1 is far more rare.

08-02-2016, 09:30 PM	#127
Nissansota240 Zilvia FREAK! Join Date: Mar 2011 Location: Land of Purple Rain Posts: 1,255 Trader Rating: (21) Feedback Score: 21 reviews	Here's the measurements on my DL adapter I'm running And the length from the face of the bell housing to the bolt holes for the shifter Sent from my SCH-I545 using Tapatalk __________________ DLG - DIRTYLOVE

08-18-2016, 05:51 AM	#131
rbs14kouki Zilvia Addict Join Date: Oct 2007 Location: Montreal , Canada Age: 37 Posts: 817 Trader Rating: (1) Feedback Score: 1 reviews	We just did a cd009 to rb25 in a r32 gts Collins plate was ruff and no instruction at all . Machined down the bellhousing to accept the plate Put every thing on the engin to figure out that the starter doesnt fit . Bellhousing need more grinding With the rb25 kit . The transmission is clocked like 4 or 5 degre (dont know if its an accident by collins) so shifter is tilting toward the driver(rhd) abit We installed 2 shifter . Firstly the serial nine We liked it because we could fine tuned our shifter position with our tilted problem ... but shift throw is super short and super easy to miss 3rd or 4th for other gears ... Second shifter and the one that is staying in GkTech Shifts are precised and not to short ... realy what i was looking for . Reverse lock out that work 100% Sit abit more back compare to serial 9 but were gona live with it since its a way better unit to our eyes __________________ AV FABRICATION Built thread sr20vet s14 http://zilvia.net/f/showthread.php?t=535574

08-18-2016, 01:08 PM	#133
RickS14 Zilvia Member Join Date: Oct 2012 Location: CLEVELAND Posts: 218 Trader Rating: (2) Feedback Score: 2 reviews	The everything cd009 swap thread. The gktech is a nice piece I sold mine already because I want to keep oem interior. So I'm going with serial nine. Any one have experience with the cbf? Sent from my iPhone using Tapatalk

08-20-2016, 08:06 PM	#148
rbs14kouki Zilvia Addict Join Date: Oct 2007 Location: Montreal , Canada Age: 37 Posts: 817 Trader Rating: (1) Feedback Score: 1 reviews	for a jz to cdxxx i would do the speedtek cut and weld bellhousing with the gktech shifter .... with that bellhousing mod you dont need to cut the tunnel ... check them out on Facebook __________________ AV FABRICATION Built thread sr20vet s14 http://zilvia.net/f/showthread.php?t=535574

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-02-2016, 01:36 AM	#122
MattTenFour Join Date: Jan 2016 Location: Holly Springs, NC Age: 38 Posts: 17 Trader Rating: (1) Feedback Score: 1 reviews	Absolutely. I wanted to make sure I wasn't missing something. The instructions that he provided did not reflect any changes to the design and said you have to grind down a portion of the starter. Just trying to iron out the details while the engine and transmission are out of the car and everything is still easy to get to.

08-02-2016, 09:47 PM	#128
RickS14 Zilvia Member Join Date: Oct 2012 Location: CLEVELAND Posts: 218 Trader Rating: (2) Feedback Score: 2 reviews	Thank you for that. Sent from my iPhone using Tapatalk

08-17-2016, 07:07 PM	#129
Johannes Zilvia Member Join Date: Feb 2009 Location: Washington Age: 30 Posts: 255 Trader Rating: (7) Feedback Score: 7 reviews	Just placed an order from a group buy going on @ cbf performance. This shifter is adjustable fore & aft as well as side to side so it fits many application. Orig price is $350. Group buy is $185. My setup is a 2J ->CD009 with Collins adapter. Here's the link to his ig page: https://www.instagram.com/cbfperformance/ Link to group buy: http://www.cbfperformance.net/store#...egory=19722030 Sent from my SAMSUNG-SM-G935A using Tapatalk

08-17-2016, 11:19 PM	#130
2muchboost Nissanaholic! Join Date: Apr 2003 Location: Austin, TX Age: 39 Posts: 2,183 Trader Rating: (33) Feedback Score: 33 reviews	Almost certain this will work for the LSX setup but can anyone confirm before I place an order?

08-19-2016, 08:34 AM	#137
RickS14 Zilvia Member Join Date: Oct 2012 Location: CLEVELAND Posts: 218 Trader Rating: (2) Feedback Score: 2 reviews	Right a jz not sr with Collins plate on a s14. It could work but I want to keep it centered as possible and under oem shifter boot. Sent from my iPhone using Tapatalk

08-19-2016, 08:52 PM	#142
undant Join Date: Aug 2016 Location: Yes Age: 36 Posts: 4 Trader Rating: (0) Feedback Score: 0 reviews	In to see if anyone can perfect the shifter setup when mated to a JZ motor.

08-20-2016, 11:09 AM	#145
Johannes Zilvia Member Join Date: Feb 2009 Location: Washington Age: 30 Posts: 255 Trader Rating: (7) Feedback Score: 7 reviews	Everyone checkout my post a couple of posts earlier. Cbf is doing a group buy on any cd009 -> jz/ls/SR to an s-chassis. Pro series utilizes adjustable fore & aft as well as side to side.

08-20-2016, 11:35 AM	#146
Johannes Zilvia Member Join Date: Feb 2009 Location: Washington Age: 30 Posts: 255 Trader Rating: (7) Feedback Score: 7 reviews	Jason's pro series will be similar to the serialnine cd999 shifter setup, except it's a fraction of its cost. $185 group buy of 50 vs $450. Sent from my SAMSUNG-SM-G935A using Tapatalk

08-20-2016, 08:43 PM	#149
lsineon Join Date: Aug 2016 Location: yes Age: 35 Posts: 4 Trader Rating: (0) Feedback Score: 0 reviews	In to see if anyone can perfect the shifter setup when mated to a JZ motor.