TX 93 240sx - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

usafboyer041288 · 07-30-2016, 10:23 AM

Sad day.. so I think the time has come that I go separate ways from the 240. Alot has been done to it

. But with marriage coming up its time to start a new chapter. So let's see..

Engine:
Blacktop Sr20det
Brian crower 264 cams
Brian crower Springs
Brian crower retainers and clips
Rocker arm stoppers
Weisco forged pistons
Forged eagle connecting rods
Hks actuator
Godspeed greedy style intake
Godspeed exhaust manifold
Unknown 750cc injectors
Enthalapy tuned ecu
Z32 maf
New dual core aluminum radiator
Dual electric fans
Wiring specialties upper/lower harness
Dual pipe down pipe
Ebay 3" exhaust
Clutch master 6 puck race clutch and flywheel

Interior:
S14 seats
Somewhat fixed dash
Circuit sport short throw shifter
Triple gauge pod
Boost gauge
Water temp gauge
Aem wide band
Oil pressure gauge

Fuel:
Walboro 255l fuel pump
Tomei fpr

Exterior:
Silvia front end (triple beams)
Duraflex front bumper
Duraflex rear bumper
Duraflex sideskirts
Xxr wheels
Dmax tailights

Brakes:
Z32 4 pot front calipers and rotors
Z32 2 pot rear calipers and rotors
Stainless steel braided lines

Suspension:
Megan racing coil overs
Godspeed front suspension
Godspeed rear control arms

Car currently doesn't run just have a few things to do to get the engine to start. Still have to have the rotors turned and brakes and clutch bled. Car started and ran fine just had a tapping noise in the head which I found out was the lobe hitting the rocker arm. I've take the lifters and bled them and haven't started it since. So a trailer will be needed to pick it up and take it home.

Sent from my SM-G930P using Tapatalk

Konabobo77 · 07-30-2016, 10:33 AM

You list all the innards and outers, but fail to mention how much you desire. How much?

usafboyer041288 · 07-30-2016, 10:43 AM

Haha oops lol im starting at 5000 obo

Sent from my SM-G930P using Tapatalk

Konabobo77 · 07-30-2016, 10:55 AM

So what exactly has to be done to get it road worthy. Don't hold back I
Am not afraid of a little car work.

usafboyer041288 · 07-30-2016, 11:10 AM

Bleed brakes bleed clutch install the bov and run vacuum hose for it. Check clearance on exhaust cam to the lifters. And bleed radiator. I have gauges for it but they have to be installed. I had oiler ones in it and never got around to running the new wires for the new gauges.

Sent from my SM-G930P using Tapatalk

usafboyer041288 · 07-31-2016, 06:10 AM

Bump

Sent from my SM-G930P using Tapatalk

dorkjoey240 · 07-31-2016, 10:21 AM

hey sir clear all ur message lol

07-30-2016, 10:23 AM	#1
usafboyer041288 Zilvia Member Join Date: Sep 2012 Location: DYESS AFB TEXAS Age: 37 Posts: 170 Trader Rating: (1) Feedback Score: 1 reviews	93 240sx Sad day.. so I think the time has come that I go separate ways from the 240. Alot has been done to it. But with marriage coming up its time to start a new chapter. So let's see.. Engine: Blacktop Sr20det Brian crower 264 cams Brian crower Springs Brian crower retainers and clips Rocker arm stoppers Weisco forged pistons Forged eagle connecting rods Hks actuator Godspeed greedy style intake Godspeed exhaust manifold Unknown 750cc injectors Enthalapy tuned ecu Z32 maf New dual core aluminum radiator Dual electric fans Wiring specialties upper/lower harness Dual pipe down pipe Ebay 3" exhaust Clutch master 6 puck race clutch and flywheel Interior: S14 seats Somewhat fixed dash Circuit sport short throw shifter Triple gauge pod Boost gauge Water temp gauge Aem wide band Oil pressure gauge Fuel: Walboro 255l fuel pump Tomei fpr Exterior: Silvia front end (triple beams) Duraflex front bumper Duraflex rear bumper Duraflex sideskirts Xxr wheels Dmax tailights Brakes: Z32 4 pot front calipers and rotors Z32 2 pot rear calipers and rotors Stainless steel braided lines Suspension: Megan racing coil overs Godspeed front suspension Godspeed rear control arms Car currently doesn't run just have a few things to do to get the engine to start. Still have to have the rotors turned and brakes and clutch bled. Car started and ran fine just had a tapping noise in the head which I found out was the lobe hitting the rocker arm. I've take the lifters and bled them and haven't started it since. So a trailer will be needed to pick it up and take it home. Sent from my SM-G930P using Tapatalk

07-31-2016, 10:21 AM	#7
dorkjoey240 Zilvia FREAK! Join Date: Dec 2006 Location: Dallas/Ft. Worth Posts: 1,042 Trader Rating: (5) Feedback Score: 5 reviews	hey sir clear all ur message lol __________________ 92 s13 coupe all stock 11-29-15

07-30-2016, 10:33 AM	#2
Konabobo77 Join Date: Jan 2014 Location: Texas Age: 35 Posts: 3 Trader Rating: (0) Feedback Score: 0 reviews	You list all the innards and outers, but fail to mention how much you desire. How much?

07-30-2016, 10:43 AM	#3
usafboyer041288 Zilvia Member Join Date: Sep 2012 Location: DYESS AFB TEXAS Age: 37 Posts: 170 Trader Rating: (1) Feedback Score: 1 reviews	Haha oops lol im starting at 5000 obo Sent from my SM-G930P using Tapatalk

07-30-2016, 10:55 AM	#4
Konabobo77 Join Date: Jan 2014 Location: Texas Age: 35 Posts: 3 Trader Rating: (0) Feedback Score: 0 reviews	So what exactly has to be done to get it road worthy. Don't hold back I Am not afraid of a little car work.

07-30-2016, 11:10 AM	#5
usafboyer041288 Zilvia Member Join Date: Sep 2012 Location: DYESS AFB TEXAS Age: 37 Posts: 170 Trader Rating: (1) Feedback Score: 1 reviews	Bleed brakes bleed clutch install the bov and run vacuum hose for it. Check clearance on exhaust cam to the lifters. And bleed radiator. I have gauges for it but they have to be installed. I had oiler ones in it and never got around to running the new wires for the new gauges. Sent from my SM-G930P using Tapatalk

07-31-2016, 06:10 AM	#6
usafboyer041288 Zilvia Member Join Date: Sep 2012 Location: DYESS AFB TEXAS Age: 37 Posts: 170 Trader Rating: (1) Feedback Score: 1 reviews	Bump Sent from my SM-G930P using Tapatalk