Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk

Tech Talk Technical Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 09-24-2008, 06:44 PM   #1
punxva
Post Whore!
 
punxva's Avatar
 
Join Date: Jan 2005
Location: Virginia Beach, Va
Age: 37
Posts: 5,730
Trader Rating: (31)
punxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfection
Feedback Score: 31 reviews
Send a message via AIM to punxva
KA Low Oil Pressure

yo my ka-t has been having some low oil pressure problems, like its fine until it warms up all the way anywhere between 50-75psi then once its warm it works its way down to 25psi at 3,000 rpms in 3rd gear. i replaced the oil pump about 2,000 miles ago hoping to fix the issue, its an oem nissan full kit. i changed the oil to 10w30, and changed the oil filter as well. i cant figure it out, any insight. btw the motor was just rebuilt about 5000 miles ago....
__________________
Slip Gypsies Blog
Quote:
Originally Posted by ixfxi View Post
not sure if you realize this

but when you knockup that skanky drunk sea donkey, you're gonna have to listen to her shit for the rest of your life

age 33 and you dont know your ass from your elbow

punxva is offline   Reply With Quote
Sponsored Links
Old 09-24-2008, 06:47 PM   #2
SoguRacing
Post Whore!
 
SoguRacing's Avatar
 
Join Date: Nov 2007
Location: (714)
Age: 39
Posts: 2,967
Trader Rating: (23)
SoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfection
Feedback Score: 23 reviews
Send a message via AIM to SoguRacing
do you have a dented oil pan? maybe the oil pickup is pressed up against the bottom of the oil pan restricting flow.
__________________
Pre Tune Checkup! Compression,LeakDown,Vacuum Test $80. Cams Install: $180
SoguRacing is offline   Reply With Quote
Old 09-24-2008, 06:50 PM   #3
punxva
Post Whore!
 
punxva's Avatar
 
Join Date: Jan 2005
Location: Virginia Beach, Va
Age: 37
Posts: 5,730
Trader Rating: (31)
punxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfection
Feedback Score: 31 reviews
Send a message via AIM to punxva
it is a little dented but not too bad, i'll take a picture tomorrow morning before work, thats the only thing i can actually think that would cause it... but at the same time wouldnt it do it all the time, not just when warmed up?
__________________
Slip Gypsies Blog
Quote:
Originally Posted by ixfxi View Post
not sure if you realize this

but when you knockup that skanky drunk sea donkey, you're gonna have to listen to her shit for the rest of your life

age 33 and you dont know your ass from your elbow

punxva is offline   Reply With Quote
Old 09-24-2008, 06:53 PM   #4
SoguRacing
Post Whore!
 
SoguRacing's Avatar
 
Join Date: Nov 2007
Location: (714)
Age: 39
Posts: 2,967
Trader Rating: (23)
SoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfectionSoguRacing is close to perfection
Feedback Score: 23 reviews
Send a message via AIM to SoguRacing
get a new oil pan anyways, especially if it the dent is in the middle or near the middle. a little dent can cause a big restriction. thats how my sr went out. spun 2 rod bearings.
__________________
Pre Tune Checkup! Compression,LeakDown,Vacuum Test $80. Cams Install: $180
SoguRacing is offline   Reply With Quote
Old 09-27-2008, 09:25 PM   #5
punxva
Post Whore!
 
punxva's Avatar
 
Join Date: Jan 2005
Location: Virginia Beach, Va
Age: 37
Posts: 5,730
Trader Rating: (31)
punxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfectionpunxva is close to perfection
Feedback Score: 31 reviews
Send a message via AIM to punxva
ok, is there anything else this could be other than the pan, just wondering so i can try different things, since it's a bitch to take the pan off the ka while its in the car, so i dont want to take it out and fix it if it really isnt the problem....
__________________
Slip Gypsies Blog
Quote:
Originally Posted by ixfxi View Post
not sure if you realize this

but when you knockup that skanky drunk sea donkey, you're gonna have to listen to her shit for the rest of your life

age 33 and you dont know your ass from your elbow

punxva is offline   Reply With Quote
Reply

Bookmarks



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 11:29 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vB.Sponsors
Copyright ? 1998 - 2022, Zilvia.net