Installed new manifold now bonnet wont close !!! - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Jay97240Sx · 06-06-2010, 11:38 AM

Hi folks, i installed a peakboost manifold over the weekend, and now the turbo sits about an inch too high and the bonnet wont close, i have nismo motor and tranny mounts. Can anyone give any suggestions what i can do to fix this issue. Im running a master power 50 trim turbo on a ka24de engine.

sliptones629 · 06-06-2010, 11:40 AM

get new motor mounts. Nismo's sit higher than stock. I put the on an everything hits. mani and hard lines, strut tower bar wont go back on and my downpipe is sitting against the floor

***CrimsonRockett*** · 06-06-2010, 11:50 AM

Look into driftfreaq's motor mounts.

I have a pair of them. Sit lower than Nismo motor mounts and doesn't let the oil pan hang below the crossmember.

Would definitely solve your clearance issue.

jspaeth · 06-06-2010, 12:08 PM

Quote:

Originally Posted by CrimsonRockett

Look into driftfreaq's motor mounts.

I have a pair of them. Sit lower than Nismo motor mounts and doesn't let the oil pan hang below the crossmember.

Would definitely solve your clearance issue.

How can it make the engine sit LOWER and also make the oil pan sit NOT AS LOW at the same time?

I am confused....

***CrimsonRockett*** · 06-06-2010, 12:14 PM

Quote:

Originally Posted by jspaeth

How can it make the engine sit LOWER and also make the oil pan sit NOT AS LOW at the same time?

I am confused....

Nismo mounts raise the engine along with the oil pan. Past the crossmember.

driftfreaq's mounts sit lower than Nismo mounts and makes the oil pan sit pretty much "flush" with the crossmember.

Not difficult to understand.

sliptones629 · 06-06-2010, 02:30 PM

I just ordered some from him right after my first post actually. Those or circuit sports. But I was hearing conflicting information. They lowered the center of gravity but sat just as high as Nismo's. I dont get it. Xsessive sells reworked brackets too that you could look into.

Jay97240Sx · 06-06-2010, 02:34 PM

Thanx for the responses guys I'm gonna look into your recommendations, and do some calling around tomorrow.

s14unimog · 06-09-2010, 02:14 PM

I think this problem is just the reality of building a car from a bunch of different mfg. Your task is to lower the turbo, so... change parts that encourage this result.

Jay97240Sx · 06-09-2010, 03:28 PM

The problem was resolved today,i bought some circuit sport engine mounts then cut them down to drop the engine as low as possible. I have more than enough clearance now.

*DALAZ_68* · 06-09-2010, 05:32 PM

those things are janky...i cant personally trust a mount, that has the rod going clear thru...

they always look like ur going to stress the rod and just warp the rubber...oppose to DF or nismo or OE mounts that put the weight on the actual rubber...

Jay97240Sx · 06-09-2010, 08:23 PM

Quote:

Originally Posted by DALAZ_68

those things are janky...i cant personally trust a mount, that has the rod going clear thru...

they always look like ur going to stress the rod and just warp the rubber...oppose to DF or nismo or OE mounts that put the weight on the actual rubber...

I understand what u are saying but in my case they were quickest solution. I had to take my nismo's off to use these which I wasnt happy about. Ill be researching a better solution in the next few weeks.

Jay97240Sx · 06-09-2010, 08:58 PM

Quote:

Originally Posted by CrimsonRockett

Look into driftfreaq's motor mounts.

I have a pair of them. Sit lower than Nismo motor mounts and doesn't let the oil pan hang below the crossmember.

Would definitely solve your clearance issue.

Just did alittle research on the driftfreaq mounts, they look almost exactly the same as the circuit sport mounts

*DALAZ_68* · 06-10-2010, 04:05 PM

big difference is there not a straight thru rod design like the CS crap...

sliptones629 · 06-10-2010, 06:39 PM

Im glad I didnt get the CS ones. They said it lowered the motors center of gravity but sat just the same height as nismos. ???????????????????????????? ezactly

Jay97240Sx · 06-10-2010, 08:09 PM

Yea they were only slightly lower than the nismo which puts them at just about stock height (they were advertised to be lower than stock), I had to cut alittle off to bring the motor down to the height I needed.

06-06-2010, 11:38 AM	#1
Jay97240Sx Leaky Injector Join Date: Jan 2009 Location: Fort Lauderdale Age: 44 Posts: 57 Trader Rating: (2) Feedback Score: 2 reviews	Installed new manifold now bonnet wont close !!! Hi folks, i installed a peakboost manifold over the weekend, and now the turbo sits about an inch too high and the bonnet wont close, i have nismo motor and tranny mounts. Can anyone give any suggestions what i can do to fix this issue. Im running a master power 50 trim turbo on a ka24de engine.

06-06-2010, 11:40 AM	#2
sliptones629 Zilvia Member Join Date: Mar 2005 Location: Washington, DC Posts: 199 Trader Rating: (0) Feedback Score: 0 reviews	get new motor mounts. Nismo's sit higher than stock. I put the on an everything hits. mani and hard lines, strut tower bar wont go back on and my downpipe is sitting against the floor __________________

06-06-2010, 02:30 PM	#6
sliptones629 Zilvia Member Join Date: Mar 2005 Location: Washington, DC Posts: 199 Trader Rating: (0) Feedback Score: 0 reviews	I just ordered some from him right after my first post actually. Those or circuit sports. But I was hearing conflicting information. They lowered the center of gravity but sat just as high as Nismo's. I dont get it. Xsessive sells reworked brackets too that you could look into. __________________

06-09-2010, 02:14 PM	#8
s14unimog Nissanaholic! Join Date: Dec 2003 Location: In a place, near a river, over a lake Age: 38 Posts: 2,415 Trader Rating: (22) Rides Gallery: s14unimog Feedback Score: 22 reviews	I think this problem is just the reality of building a car from a bunch of different mfg. Your task is to lower the turbo, so... change parts that encourage this result. __________________ Fuking ginger bread man stole my wallet... SHIFT*lock_slide to side d3m3rs0n: if i have a baby im naming it Brandons Fault Emerson

06-09-2010, 05:32 PM	#10
DALAZ_68 not giving a fuck Join Date: Apr 2007 Location: Los angeles Age: 38 Posts: 15,077 Trader Rating: (104) Feedback Score: 104 reviews	those things are janky...i cant personally trust a mount, that has the rod going clear thru... they always look like ur going to stress the rod and just warp the rubber...oppose to DF or nismo or OE mounts that put the weight on the actual rubber... __________________ LOL 240... whats better than 1? 5 1's ...lol PSN & XBL GT : Wh0pp3r68 CLUB LEXUS : Wh0pp3r

06-06-2010, 02:34 PM	#7
Jay97240Sx Leaky Injector Join Date: Jan 2009 Location: Fort Lauderdale Age: 44 Posts: 57 Trader Rating: (2) Feedback Score: 2 reviews	Thanx for the responses guys I'm gonna look into your recommendations, and do some calling around tomorrow.

06-09-2010, 03:28 PM	#9
Jay97240Sx Leaky Injector Join Date: Jan 2009 Location: Fort Lauderdale Age: 44 Posts: 57 Trader Rating: (2) Feedback Score: 2 reviews	The problem was resolved today,i bought some circuit sport engine mounts then cut them down to drop the engine as low as possible. I have more than enough clearance now.

06-10-2010, 04:05 PM	#13
DALAZ_68 not giving a fuck Join Date: Apr 2007 Location: Los angeles Age: 38 Posts: 15,077 Trader Rating: (104) Feedback Score: 104 reviews	big difference is there not a straight thru rod design like the CS crap... __________________ LOL 240... whats better than 1? 5 1's ...lol PSN & XBL GT : Wh0pp3r68 CLUB LEXUS : Wh0pp3r

06-10-2010, 06:39 PM	#14
sliptones629 Zilvia Member Join Date: Mar 2005 Location: Washington, DC Posts: 199 Trader Rating: (0) Feedback Score: 0 reviews	Im glad I didnt get the CS ones. They said it lowered the motors center of gravity but sat just the same height as nismos. ???????????????????????????? ezactly __________________

06-10-2010, 08:09 PM	#15
Jay97240Sx Leaky Injector Join Date: Jan 2009 Location: Fort Lauderdale Age: 44 Posts: 57 Trader Rating: (2) Feedback Score: 2 reviews	Yea they were only slightly lower than the nismo which puts them at just about stock height (they were advertised to be lower than stock), I had to cut alittle off to bring the motor down to the height I needed.