WI Built Sr, IHI Turbo, Race Part out, Crazy Garage cleaning, Spare Parts Everywhere - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

mazdaRX7Galantvr4 · 11-13-2010, 04:05 PM

Name: Darin O.
Location: Appleton, WI
Zip: 54915
Phone: 9209155215
Email: [email protected]

Shipping: Yes

I've decided to get out of the game for a little bit and take a break, getting married and moving out sale.

Engine
*$1200*
Built Sr20 Redtop

Wiesco Pistons 9.0 Compression
Eagle Rods
ARP Head Studs
ACL main and rod Bearings
Cosworth Head gasket
Always Ran setrab oil cooler and never overheated, frequent oil changes with Brad Penn Oil
Front End Accessories Included Power steering pump, Water Pump with Underdrive Pulley, Alternator, Modified Valve Cover for better Breather set up

*story on engine...Running with stock cams, has a little piston noise due to close to race clearances. Engine made 355hp/318tq with turbo im selling as well.

Sr20det redtop Parts

Bare Block flawless cylinder walls, stock bore $200
Crankshaft, fresh polishing $120
Upper Oil Pan $40
Lower Oil Pan $70
Front Cover $70
Oil Pick Up $20
Thermostat Housing $10
Water Neck Off Head $30
Water Neck Modified Like T28 plus sensor port and Breather Tapped $75
Coil Packs x4 $15 Each
Coil Pack Harness Modified $40
Coil Pack Cover/Spark Cover $10
Oil Dipstick Tube $10
Oil Dipstick Rod x 2 $10
Heater Hoses under Intake Manifold misc $5
Valve Cover $35
Water Pump $25
Throttle Body stock $15
Cam Angle Sensor without plastic Cover $30

Performance/ Aftermarket Parts

Custom sized intercooler, fits infront of Radiator, Couplers, Clamps, leftover pipes Included $600

Forced Performance 18g Turbo, Manifold, Downpipe Tig welded, Lines SOLD
*355hp/318 tq @23psi on E85
*Crazy spool 3800rp full boost, no lag compared to garrett 2871
*Water/ Oil Cooled
*Includes Ceramic coated Megan Manifold
*Doesn't Blow gaskets like T2, T3 flanged turbos

Similar to Power Enterprise Kit that sells for $1300 Power Enterprise Bottom Mount Turbo Kit : SR20DET

Tial BOV, no flange $150
Intake manifold plastic spacer, prevents heat transfer x 2 $15 Each
Power steering Coolers tube and Fin 6x6in, 12x6 $10 Each
Nismo Oil Cap $30
Nismo Lightened Flywheel $75
Engine Mounts, 1 stock with window weld, 1 aftermarket hardened/aluminum $30
Oil Cooler sandwich, 2 ports for sensors $40
Garrett gti-R T28 Turbo $300

Other Stock Parts

Sr Gutted wiring harness $75
Sr20 Transmission $150
Sr Crankshaft Pulley $15
Stock Shifter $10
S13 Nissan Clutch master x2 $15 Each
S13 Clutch Hardline $10
S13 Transmission Brace x 2 $15 Each
S13 Transmission Mount Bushing $5
Sr Clutch Fork $10
S13 Speed Sensor $20
S14 Wiper Amplifier $10
S14 Auto Ecu $10

projectslider · 11-13-2010, 04:56 PM

let me know shipping for the 18g kit to zip 00926!!!

mazdaRX7Galantvr4 · 11-13-2010, 05:00 PM

Ill do it for 650 shipped, lots of weight and downpipe, lines, intake pipe if you want it included

projectslider · 11-13-2010, 06:30 PM

alright ! i will pm u tommorow
thanks

htownsr510 · 11-13-2010, 06:31 PM

Details on gtir turbo miles condition etc

*brndck* · 11-13-2010, 06:37 PM

appleton woot! i was there in march.
houdini's bar is cool.
glws.

jarend · 11-13-2010, 08:50 PM

pming about valve cover shipped to 92122. Thanks.

mazdaRX7Galantvr4 · 11-13-2010, 09:01 PM

Quote:

Originally Posted by htownsr510

Details on gtir turbo miles condition etc

Good shape, I bought it used and put on 10k without problems. Normal shaft play, endplay normal. I had to use the lines. And fittings for my current turbo so only receiving turbo with wastegate and adjustable actuator.

projectslider · 11-15-2010, 05:37 PM

still have the turbo kit available?

mazdaRX7Galantvr4 · 11-16-2010, 08:18 AM

Quote:

Originally Posted by projectslider

still have the turbo kit available?

Yes I do, also the intercooler kit to go with it with piping/couplers/bov

mazdaRX7Galantvr4 · 11-17-2010, 07:18 PM

Quote:

Originally Posted by jarend

pming about valve cover shipped to 92122. Thanks.

Shipped your valve cover for you, thanks.

mazdaRX7Galantvr4 · 11-21-2010, 08:40 AM

Updated sold parts

mazdaRX7Galantvr4 · 11-25-2010, 09:49 AM

To the top

oligator20 · 11-25-2010, 10:45 AM

Whats the weight of the flywheel? In good condition need to be resurfaced? Pm me the info please and if you can ship. Thanks

mazdaRX7Galantvr4 · 11-25-2010, 12:36 PM

Quote:

Originally Posted by oligator20

Whats the weight of the flywheel? In good condition need to be resurfaced? Pm me the info please and if you can ship. Thanks

the flywheel is probably between 10-12 pounds never weighed it. The surface is good, if you wanted it perfect you can resurface, but can run a clutch on it without troubles.

I will ship it for you if needed, throw in some extra for that and its yours.

oligator20 · 11-25-2010, 02:41 PM

Are you sure its a nismo? I check on google and the machining is very different... You see a stamp nismo on the flywheel?

mazdaRX7Galantvr4 · 11-25-2010, 03:11 PM

I was told it was a nismo when I had it by someone, I thought it was because it also had a nismo clutch that I had.

I just inspected the flywheel that there isn't any markings of a brand.

mazdaRX7Galantvr4 · 11-28-2010, 12:59 PM

Turbo is sold

mazdaRX7Galantvr4 · 11-28-2010, 02:22 PM

More pictures and more parts

If you see something without a price that I do not have listed above in my first post make me an offer.

I have soooo much extra hardware from my cars over the years (this is only a 1/4 of it) pertaining to Nissan and SR20's. If you need anything from oil pan bolts to dipsticks, rear main seal bolts, whatever I probably have it and will sell for cheap as shit.

*racerx2k1* · 11-28-2010, 02:25 PM

Quote:

Originally Posted by mazdaRX7Galantvr4

Updated sold parts

Quote:

Originally Posted by mazdaRX7Galantvr4

To the top

Quote:

Originally Posted by mazdaRX7Galantvr4

Turbo is sold

Quote:

Originally Posted by mazdaRX7Galantvr4

More pictures and more parts

If you see something without a price that I do not have listed above in my first post make me an offer.

I have soooo much extra hardware from my cars over the years (this is only a 1/4 of it) pertaining to Nissan and SR20's. If you need anything from oil pan bolts to dipsticks, rear main seal bolts, whatever I probably have it and will sell for cheap as shit.

2 bump limit. You can start new thread in 3 days.

11-13-2010, 04:05 PM	#1
mazdaRX7Galantvr4 Zilvia Member Join Date: Aug 2005 Location: Wisonsin Age: 39 Posts: 194 Trader Rating: (9) Feedback Score: 9 reviews	Built Sr, IHI Turbo, Race Part out, Crazy Garage cleaning, Spare Parts Everywhere Name: Darin O. Location: Appleton, WI Zip: 54915 Phone: 9209155215 Email: [email protected] Shipping: Yes I've decided to get out of the game for a little bit and take a break, getting married and moving out sale. Engine $1200 Built Sr20 Redtop Wiesco Pistons 9.0 Compression Eagle Rods ARP Head Studs ACL main and rod Bearings Cosworth Head gasket Always Ran setrab oil cooler and never overheated, frequent oil changes with Brad Penn Oil Front End Accessories Included Power steering pump, Water Pump with Underdrive Pulley, Alternator, Modified Valve Cover for better Breather set up story on engine...Running with stock cams, has a little piston noise due to close to race clearances. Engine made 355hp/318tq with turbo im selling as well. Sr20det redtop Parts* Bare Block flawless cylinder walls, stock bore $200 Crankshaft, fresh polishing $120 Upper Oil Pan $40 Lower Oil Pan $70 Front Cover $70 Oil Pick Up $20 Thermostat Housing $10 Water Neck Off Head $30 Water Neck Modified Like T28 plus sensor port and Breather Tapped $75 Coil Packs x4 $15 Each Coil Pack Harness Modified $40 Coil Pack Cover/Spark Cover $10 Oil Dipstick Tube $10 Oil Dipstick Rod x 2 $10 Heater Hoses under Intake Manifold misc $5 Valve Cover $35 Water Pump $25 Throttle Body stock $15 Cam Angle Sensor without plastic Cover $30 Performance/ Aftermarket Parts Custom sized intercooler, fits infront of Radiator, Couplers, Clamps, leftover pipes Included $600 Forced Performance 18g Turbo, Manifold, Downpipe Tig welded, Lines SOLD 355hp/318 tq @23psi on E85 Crazy spool 3800rp full boost, no lag compared to garrett 2871 Water/ Oil Cooled Includes Ceramic coated Megan Manifold Doesn't Blow gaskets like T2, T3 flanged turbos Similar to Power Enterprise Kit that sells for $1300 Power Enterprise Bottom Mount Turbo Kit : SR20DET Tial BOV, no flange $150 Intake manifold plastic spacer, prevents heat transfer x 2 $15 Each Power steering Coolers tube and Fin 6x6in, 12x6 $10 Each Nismo Oil Cap $30 Nismo Lightened Flywheel $75 Engine Mounts, 1 stock with window weld, 1 aftermarket hardened/aluminum $30 Oil Cooler sandwich, 2 ports for sensors $40 Garrett gti-R T28 Turbo $300 Other Stock Parts* Sr Gutted wiring harness $75 Sr20 Transmission $150 Sr Crankshaft Pulley $15 Stock Shifter $10 S13 Nissan Clutch master x2 $15 Each S13 Clutch Hardline $10 S13 Transmission Brace x 2 $15 Each S13 Transmission Mount Bushing $5 Sr Clutch Fork $10 S13 Speed Sensor $20 S14 Wiper Amplifier $10 S14 Auto Ecu $10 Last edited by mazdaRX7Galantvr4; 11-28-2010 at 12:59 PM..

11-13-2010, 04:56 PM	#2
projectslider Zilvia Junkie Join Date: Apr 2007 Location: COLUMBIA, SC Age: 40 Posts: 473 Trader Rating: (1) Feedback Score: 1 reviews	let me know shipping for the 18g kit to zip 00926!!!

11-13-2010, 05:00 PM	#3
mazdaRX7Galantvr4 Zilvia Member Join Date: Aug 2005 Location: Wisonsin Age: 39 Posts: 194 Trader Rating: (9) Feedback Score: 9 reviews	Ill do it for 650 shipped, lots of weight and downpipe, lines, intake pipe if you want it included

11-13-2010, 06:30 PM	#4
projectslider Zilvia Junkie Join Date: Apr 2007 Location: COLUMBIA, SC Age: 40 Posts: 473 Trader Rating: (1) Feedback Score: 1 reviews	alright ! i will pm u tommorow thanks

11-13-2010, 06:31 PM	#5
htownsr510 Zilvia Member Join Date: Jan 2010 Location: se houston Age: 43 Posts: 156 Trader Rating: (3) Feedback Score: 3 reviews	Details on gtir turbo miles condition etc

11-13-2010, 08:50 PM	#7
jarend Zilvia Junkie Join Date: Aug 2009 Location: San Diego Posts: 410 Trader Rating: (27) Feedback Score: 27 reviews	pming about valve cover shipped to 92122. Thanks.

11-15-2010, 05:37 PM	#9
projectslider Zilvia Junkie Join Date: Apr 2007 Location: COLUMBIA, SC Age: 40 Posts: 473 Trader Rating: (1) Feedback Score: 1 reviews	still have the turbo kit available?

11-21-2010, 08:40 AM	#12
mazdaRX7Galantvr4 Zilvia Member Join Date: Aug 2005 Location: Wisonsin Age: 39 Posts: 194 Trader Rating: (9) Feedback Score: 9 reviews	Updated sold parts

11-25-2010, 09:49 AM	#13
mazdaRX7Galantvr4 Zilvia Member Join Date: Aug 2005 Location: Wisonsin Age: 39 Posts: 194 Trader Rating: (9) Feedback Score: 9 reviews	To the top

11-25-2010, 10:45 AM	#14
oligator20 Join Date: Nov 2007 Location: quebec Age: 37 Posts: 20 Trader Rating: (0) Feedback Score: 0 reviews	Whats the weight of the flywheel? In good condition need to be resurfaced? Pm me the info please and if you can ship. Thanks

11-25-2010, 02:41 PM	#16
oligator20 Join Date: Nov 2007 Location: quebec Age: 37 Posts: 20 Trader Rating: (0) Feedback Score: 0 reviews	Are you sure its a nismo? I check on google and the machining is very different... You see a stamp nismo on the flywheel?

11-25-2010, 03:11 PM	#17
mazdaRX7Galantvr4 Zilvia Member Join Date: Aug 2005 Location: Wisonsin Age: 39 Posts: 194 Trader Rating: (9) Feedback Score: 9 reviews	I was told it was a nismo when I had it by someone, I thought it was because it also had a nismo clutch that I had. I just inspected the flywheel that there isn't any markings of a brand.

11-28-2010, 12:59 PM	#18
mazdaRX7Galantvr4 Zilvia Member Join Date: Aug 2005 Location: Wisonsin Age: 39 Posts: 194 Trader Rating: (9) Feedback Score: 9 reviews	Turbo is sold

11-28-2010, 02:22 PM	#19
mazdaRX7Galantvr4 Zilvia Member Join Date: Aug 2005 Location: Wisonsin Age: 39 Posts: 194 Trader Rating: (9) Feedback Score: 9 reviews	More pictures and more parts If you see something without a price that I do not have listed above in my first post make me an offer. I have soooo much extra hardware from my cars over the years (this is only a 1/4 of it) pertaining to Nissan and SR20's. If you need anything from oil pan bolts to dipsticks, rear main seal bolts, whatever I probably have it and will sell for cheap as shit.