engine/engine bay photos

[LiveLowSilvia]

Originally Posted by Corbic

Why only 5psi?

I need a new boost controller. My AEM is throwing an error code for whatever reason. Everything is hooked up proper. Even the tuner looked it over. I have an HKS controller waiting for me then all ill need is new couplers before I can get some real numbers.

[LiveLowSilvia]

Originally Posted by cured13

don't be shy LiveLowSilvia, show us some more pics,
how did you mount the rad at the bottom and what fans are you using.
Did you kept the A/C?
Any shots from above, and under the engine?

Nothing fancy under there at all haha! I literally jus found some brackets in my garage and bent them accordingly. Then mounted the Rad with 10mm bolts. Dual electric fans are wired up to a switch.
No power steering, No A/C.. Haha

[SR520]

Here's mine engine bay,It's a S13 Blacktop with #62 ecu in a 1968 Datsun 520 pick-up.


This one is my buddy's Im finishing the swap for him,It's a S15 n/a in a 1974 Datsun 620 P/U.

[bmcreider]

Originally Posted by LiveLowSilvia

What boost u running, 7psi?
Definitely recommend getting some cams.
After being down for almost 2 years, my baby is finally up and running.
It's on a really mild tune. Until I get a new boost controller and better couplers, I'm stuck at 301hp at only 5psi.

880cc, full head build; cams, oversized valves, etc., T3 .50 trim replica, with AEM series 2 EMS. I'm going for 450hp down the road but realistically can sit at 400 all day with the right parts and better tune.

Rules:

7psi holy shit I wish.

That was running @ 16psi. The car had an old tune from an old SR motor in it, dropped a new motor in, and the dude made me wait 1.5 hours outside like an idiot while he chatted up someone else....then when he tuned it he basically ran the dyno a few times, adjusted for knock, and tuned the AFR for a slow cruising speed. Rip off. I can get a good tune across the board, but it'll set me back $500.

[BlewByYou]

S14 Pro Am Drift Car coming along as i get time to work on it. I was recently sponsored for 2014 Pro Am so trying to get her finish by Nov.

Rb25 with Rb26 internals, ARP Main Studs/Head Studs/Rod Bolts, ACL bearings, N1 Pumps, Over $1000 in Poldyn oil shedding and Friction coating, HKS cams, R34 Cas, ATI balancer, Greddy manifold, 1000cc Injectors, Gt35 Turbo, OsGiken Alum Clutch, AEM Ecu, LS2 coils, etc....

Shooting for 600whp Stock Block

Driftworks Full Suspension, Fortune Auto Coilovers, Fuel Cell, Aftermarket Industries Surge Tank, Chasebays Harness, Chasebays Brake/Clutch Lines, Custom Wilwood Setup front and Rear.

[PoorMans180SX]

^Very nice, I dig the gold on black on gold, haha.

Just got everything to finish mine up.

[Kallixtos]

I didn't like the way all the polished Greddy IC kit looked, so I painted it. And bought some 4-ply black couplers.

[sil14zenki]

i agree, looks better in black and for some reason i've never liked blue couplers either

[killer240]

It's not mine, but it's so clean. Happy thirsty Thursday DROOOOLING. Why don't we have a drooling smiley face?


7961734566_1df49554eb_o by d_2jzgte, on Flickr

7961733938_c7b4fb0042_o by d_2jzgte, on Flickr

7961733518_14b85c5b4f_o by d_2jzgte, on Flickr

7961733000_999f4be479_o by d_2jzgte, on Flickr

7961732508_a64b4425e9_o by d_2jzgte, on Flickr

[turbo2nr]

i guess i can finally post this in here 90% complete..



all work done by tm_spl, tarmac motorsports.

[ka-titties]

Originally Posted by killer240

[/url]

all that fab work and they couldn't tap a damn hole for the temp sensor?

[jr_ss]

Originally Posted by ka-titties

all that fab work and they couldn't tap a damn hole for the temp sensor?

They make those nice plates that wedge between the head and the outlet pipe too...

[Matej]

Originally Posted by jr_ss

They make those nice plates that wedge between the head and the outlet pipe too...

People have problems with those reading the temperature too hot, since they are so close to the block and exhaust.

[xBtony]

Shitty iPhone pic of a shitty single cam lol

[O$mo]

[yetijeff]

Originally Posted by xBtony

Shitty iPhone pic of a shitty single cam lol

Hell ya 👍.....

[SupaDoopa]

Originally Posted by ka-titties

all that fab work and they couldn't tap a damn hole for the temp sensor?

Actually, the way he did it was correct. Mid way in the hose with a proper adapter. As stated, those plates have tendency to have inaccurate readings. It's not the most visually appealing thing but it works and works well.

[unwtdhero]

The plate is too close to the turbo, it will make it read hot.

[NotLowEnough]

My piece of shit. Planning relocating fuel filter and power steering reservoir.

[Perfect Balance]

[rbs14kouki]

my DocRace manifold just came in friday !!!!





cant wait to get a turbo to slap it on !!! and in the car after
if only i could sale my kouki front end (localy) to get abit of $$$

[SupaDoopa]

^ Holy shit.

That is all.

[ka-titties]

that manifold is a work of art

[ch1873857]

ehh it aint too pretty but its super functional. got fucked on a tow and drove it an hour an 30 to the track. stayed very cool.

[XxNickxX]

Originally Posted by DOD

My almost ready enginebay in my ps13.



More pics here:
DOD PS13 Blog | DOD JDM Blog
http://www.facebook.com/DODPS13

Definitely like the color combo here! Looks really good!

[Ikera]

wow I feel so small here with all these powerful engines

here is my SOHC :P

[scir16v]

My crappy looking bay from a few weeks ago. Just a factory looking engine.




No idea why it turned the picture sideways.

[Reece]

Originally Posted by Ikera

wow I feel so small here with all these powerful engines

here is my SOHC :P

What front end is that?

Honestly it doesn't look bad.

[tapdeznutz]

Originally Posted by Ikera

wow I feel so small here with all these powerful engines

here is my SOHC :P

not at all bro, much respect!!! you will be my inspiration for my single slammer turbo project!!! REP IT!!!

[crzsteveo]

KA all the way!