need help on 240SX - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Premier240 · 04-13-2005, 05:35 PM

Whats up guys i need some help i have a automatic 92 240 i just replaced the tranny on it. Now it doesn't even want to kick over it does nothing when i turn the key to the the start position. I don't know what to do i checked everything and still nothing. I have a feeling it is grounding problem but i dont know where. If you guys can help me out with any info i would appreciate it i need help bad.

Thanks,
Anthony

sLip techniques · 04-13-2005, 05:51 PM

have you checked the starter?

Premier240 · 04-13-2005, 05:56 PM

i dont thing it is the starter because the motor turned over without a problem right before i changed the tranny. Could the starter have gone out since then. Is there anyway to check to see if it is the starter?

Thanks,
Anthony

Maeda · 04-13-2005, 05:57 PM

Does it just click?

Double check the starter wires, and make sure they are grounded for sure.

Try and tap the starter with a hammer and see if it helps any.

If it started fine then you probably don't have the wires hooked up properly or at all... Make sure they didn't fall off. The ground tends to do that to me...

AllenRPS13 · 04-13-2005, 06:16 PM

does your battery loose? or may be the starter got some problem, try to use something to hit the starter motor a few time then try to start it again, it may work for u, at least work for me last time

240silvia · 04-13-2005, 06:39 PM

Maybe the starter isn't placed into the trans properly. I 2nd the battery check. Also... make sure the starter wires are put in the right place.

TheTicTac · 04-13-2005, 06:49 PM

Maybe you didn't jump the neutral switch.

Premier240 · 04-13-2005, 08:10 PM

TheTicTac your are right it was the neutral switch and now the car starts fine. Now when i drove the the car it drove fine until i got around 40 mph and then the car doesn't not want to go anymore and the rpms start to rise. But when i put it in 2nd the cars accelerates past 40 and keeps going but it sounds like the engine is working hard. Could i have put the torque converter in wrong or what. Any help would be great.

Thanks,
Anthony

sLip techniques · 04-13-2005, 08:54 PM

sensors on the tranmission?

Premier240 · 04-13-2005, 11:15 PM

i have the other sensors on the old tranny so can i switch them out.

Thanks
Anthony

TheTicTac · 04-14-2005, 05:01 AM

Actually you kinda don't need the other sensors, the main one you need is the speed sensor. Did you properly install the pressure plate back on? You have to torque it in a criss cross pattern, also did you resurface the flywheel or get a new T/O bearing?

s13gonwild · 04-14-2005, 06:28 AM

blah i didnt see that post of you finding a solution.

Premier240 · 04-14-2005, 12:08 PM

It is a automatic so it don't have a pressure plate or t/o bearing. I think it might be the speed sensor or another hommie told me it might be the cable next to the throttle cable. The problem that im having is that it seems to not want to shift correctly. So if any of you guys have solutions im open to any.

Thanks,
Anthony

TheTicTac · 04-14-2005, 01:39 PM

Oh I thought you swapped your tranny out with a 5spd. Well check if you have everything connected, IIRC there is a resistor near the powersteering resv. that does causes the tranny to behave weird when not plugged in.

04-13-2005, 05:35 PM	#1
Premier240 Join Date: Feb 2005 Location: CA Posts: 21 Trader Rating: (0) Feedback Score: 0 reviews	need help on 240SX Whats up guys i need some help i have a automatic 92 240 i just replaced the tranny on it. Now it doesn't even want to kick over it does nothing when i turn the key to the the start position. I don't know what to do i checked everything and still nothing. I have a feeling it is grounding problem but i dont know where. If you guys can help me out with any info i would appreciate it i need help bad. Thanks, Anthony

04-13-2005, 05:57 PM	#4
Maeda Nissanaholic! Join Date: Dec 2002 Location: Camp Snake Bite, CA RIP Posts: 2,356 Trader Rating: (0) Rides Gallery: Maeda Feedback Score: 0 reviews	Does it just click? Double check the starter wires, and make sure they are grounded for sure. Try and tap the starter with a hammer and see if it helps any. If it started fine then you probably don't have the wires hooked up properly or at all... Make sure they didn't fall off. The ground tends to do that to me... __________________

04-13-2005, 06:16 PM	#5
AllenRPS13 Zilvia FREAK! Join Date: Sep 2004 Location: Bay Area (East Bay) Age: 41 Posts: 1,294 Trader Rating: (0) Feedback Score: 0 reviews	does your battery loose? or may be the starter got some problem, try to use something to hit the starter motor a few time then try to start it again, it may work for u, at least work for me last time __________________ ~小アレンのリベリオン~ いくせ, 勝負た! 轟こう, オレのKRMS13!!! オレの得意技！蹴り進入！角度の少ないドリフト！

04-13-2005, 06:49 PM	#7
TheTicTac Zilvia Junkie Join Date: May 2002 Location: CA Posts: 449 Trader Rating: (0) Feedback Score: 0 reviews	Maybe you didn't jump the neutral switch. __________________ GorgeousGarage L.oose S.ocks D.aisuke !

04-14-2005, 05:01 AM	#11
TheTicTac Zilvia Junkie Join Date: May 2002 Location: CA Posts: 449 Trader Rating: (0) Feedback Score: 0 reviews	Actually you kinda don't need the other sensors, the main one you need is the speed sensor. Did you properly install the pressure plate back on? You have to torque it in a criss cross pattern, also did you resurface the flywheel or get a new T/O bearing? __________________ GorgeousGarage L.oose S.ocks D.aisuke !

04-13-2005, 05:51 PM	#2
sLip techniques Zilvia Member Join Date: Apr 2005 Location: So Cal Posts: 292 Trader Rating: (0) Feedback Score: 0 reviews	have you checked the starter?

04-13-2005, 05:56 PM	#3
Premier240 Join Date: Feb 2005 Location: CA Posts: 21 Trader Rating: (0) Feedback Score: 0 reviews	i dont thing it is the starter because the motor turned over without a problem right before i changed the tranny. Could the starter have gone out since then. Is there anyway to check to see if it is the starter? Thanks, Anthony

04-13-2005, 06:39 PM	#6
240silvia Nissanaholic! Join Date: Jul 2002 Location: Wilmington NC Age: 40 Posts: 2,060 Trader Rating: (3) Feedback Score: 3 reviews	Maybe the starter isn't placed into the trans properly. I 2nd the battery check. Also... make sure the starter wires are put in the right place.

04-13-2005, 08:10 PM	#8
Premier240 Join Date: Feb 2005 Location: CA Posts: 21 Trader Rating: (0) Feedback Score: 0 reviews	TheTicTac your are right it was the neutral switch and now the car starts fine. Now when i drove the the car it drove fine until i got around 40 mph and then the car doesn't not want to go anymore and the rpms start to rise. But when i put it in 2nd the cars accelerates past 40 and keeps going but it sounds like the engine is working hard. Could i have put the torque converter in wrong or what. Any help would be great. Thanks, Anthony

04-13-2005, 08:54 PM	#9
sLip techniques Zilvia Member Join Date: Apr 2005 Location: So Cal Posts: 292 Trader Rating: (0) Feedback Score: 0 reviews	sensors on the tranmission?

04-13-2005, 11:15 PM	#10
Premier240 Join Date: Feb 2005 Location: CA Posts: 21 Trader Rating: (0) Feedback Score: 0 reviews	i have the other sensors on the old tranny so can i switch them out. Thanks Anthony

04-14-2005, 06:28 AM	#12
s13gonwild BANNED Join Date: Jan 2005 Location: cali Posts: 466 Trader Rating: (0) Feedback Score: 0 reviews	blah i didnt see that post of you finding a solution.

04-14-2005, 12:08 PM	#13
Premier240 Join Date: Feb 2005 Location: CA Posts: 21 Trader Rating: (0) Feedback Score: 0 reviews	It is a automatic so it don't have a pressure plate or t/o bearing. I think it might be the speed sensor or another hommie told me it might be the cable next to the throttle cable. The problem that im having is that it seems to not want to shift correctly. So if any of you guys have solutions im open to any. Thanks, Anthony

04-14-2005, 01:39 PM	#14
TheTicTac Zilvia Junkie Join Date: May 2002 Location: CA Posts: 449 Trader Rating: (0) Feedback Score: 0 reviews	Oh I thought you swapped your tranny out with a 5spd. Well check if you have everything connected, IIRC there is a resistor near the powersteering resv. that does causes the tranny to behave weird when not plugged in. __________________ GorgeousGarage L.oose S.ocks D.aisuke !