rx7 lug pattern - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

YoungRookie · 05-16-2004, 03:11 PM

What is the lug pattern of the 4 lug turbo ll rx7's? If they are 114.3 i can get a good deal on them from one of my buddies here in town. thanks in advance

NismoSilvia270R · 05-16-2004, 03:31 PM

rx-7 turbo II and gtu and gxl are all 5lug

thelinja · 05-16-2004, 03:33 PM

1. There were no 4-lug TII wheels. Only base model S4's(86-88) were 4 lug. The lug patterns are 4x114.3 and 5x114.3.

2. The center bore on RX-7 wheels is too small for the 240SX hubs, therefore, the wheels will not fit.

richardxfeng · 05-16-2004, 03:41 PM

sorry for hijacking the thread.i was wondering if Mazda have same size wheel nuts as toyota?thanks!

DRFT · 05-16-2004, 04:06 PM

86 have 4x114

sw20 have 5 x 114

SilviaDriver · 05-16-2004, 06:56 PM

RX7 = 240sx?

if so, then this is the correct section =]

YoungRookie · 05-16-2004, 08:11 PM

Okay ig uess the car was not a turbo ll i was told it was, but i saw the wheels and they are 4 lug, but they will absolutley not fit?

thelinja · 05-16-2004, 09:15 PM

Unless you bore the center a few mm's, no they won't fit.

boro240 · 05-16-2004, 09:39 PM

also, do FCs have the same offset as FDs? cause FD wheels are +50.

thelinja · 05-16-2004, 11:34 PM

All FC wheels are +40.

richardxfeng · 05-17-2004, 12:48 AM

Quote:

Originally Posted by DRFT

86 have 4x114

sw20 have 5 x 114

i was alking about wheel nuts size,not the bolt pattern.

DRFT · 05-17-2004, 12:53 AM

i dont think so, only nissan and subaru share the same pattern. the rest is honda toyota and others i tihnk

YoungRookie · 05-17-2004, 06:33 AM

How hard would it be to bore the center out a few mm's? or how much would it cost to get done?

thelinja · 05-17-2004, 09:42 AM

Boring out the center of a wheel seems like a pain in the ass. I suppose you could use a dremel with a carbide bit, but it would be hard to get it uniform. What wheels are these anyway? Because the only 4 lug FC wheel I can think of is the phone dial looking one and that wheel is 14x5.5".

YoungRookie · 05-17-2004, 03:37 PM

The wheels look like the watanabe rs8, i have seen these on a 240z before too and they look good.I dont think they are stock rx7 wheels

thelinja · 05-17-2004, 10:55 PM

Well, if it isn't a stock Mazda wheel, you should test fit it because chances are the center bore would fit the 240 hub.

mav1178 · 05-18-2004, 03:46 AM

Quote:

Originally Posted by thelinja

Boring out the center of a wheel seems like a pain in the ass. I suppose you could use a dremel with a carbide bit, but it would be hard to get it uniform. What wheels are these anyway? Because the only 4 lug FC wheel I can think of is the phone dial looking one and that wheel is 14x5.5".

Any machine shop with a CNC machine can bore the center of a wheel out. You'd need it at least 66.1mm for a Nissan center bore.

-alex

05-16-2004, 03:11 PM	#1
YoungRookie Zilvia FREAK! Join Date: Mar 2003 Location: Geencastle, PA Age: 35 Posts: 1,068 Trader Rating: (3) Feedback Score: 3 reviews	rx7 lug pattern What is the lug pattern of the 4 lug turbo ll rx7's? If they are 114.3 i can get a good deal on them from one of my buddies here in town. thanks in advance __________________ 92 Hatch, KA-T, T28, 12 PSI, FMIC, 3" TBE, EFI ECU, 440cc Inj, And more...

05-16-2004, 04:06 PM	#5
DRFT Post Whore! Join Date: Apr 2003 Location: Pow Pow Age: 40 Posts: 3,744 Trader Rating: (0) Feedback Score: 0 reviews	86 have 4x114 sw20 have 5 x 114 __________________ ApexNetwork.Net Sacramento & Norcal Forum

05-16-2004, 08:11 PM	#7
YoungRookie Zilvia FREAK! Join Date: Mar 2003 Location: Geencastle, PA Age: 35 Posts: 1,068 Trader Rating: (3) Feedback Score: 3 reviews	Okay ig uess the car was not a turbo ll i was told it was, but i saw the wheels and they are 4 lug, but they will absolutley not fit? __________________ 92 Hatch, KA-T, T28, 12 PSI, FMIC, 3" TBE, EFI ECU, 440cc Inj, And more...

05-17-2004, 12:53 AM	#12
DRFT Post Whore! Join Date: Apr 2003 Location: Pow Pow Age: 40 Posts: 3,744 Trader Rating: (0) Feedback Score: 0 reviews	i dont think so, only nissan and subaru share the same pattern. the rest is honda toyota and others i tihnk __________________ ApexNetwork.Net Sacramento & Norcal Forum

05-17-2004, 06:33 AM	#13
YoungRookie Zilvia FREAK! Join Date: Mar 2003 Location: Geencastle, PA Age: 35 Posts: 1,068 Trader Rating: (3) Feedback Score: 3 reviews	How hard would it be to bore the center out a few mm's? or how much would it cost to get done? __________________ 92 Hatch, KA-T, T28, 12 PSI, FMIC, 3" TBE, EFI ECU, 440cc Inj, And more...

05-16-2004, 03:31 PM	#2
NismoSilvia270R Zilvia Junkie Join Date: Jan 2004 Location: Clarksville Age: 38 Posts: 510 Trader Rating: (1) Feedback Score: 1 reviews	rx-7 turbo II and gtu and gxl are all 5lug

05-16-2004, 03:33 PM	#3
thelinja Zilvia FREAK! Join Date: Jul 2002 Location: New Jersey Posts: 1,466 Trader Rating: (3) Rides Gallery: thelinja Feedback Score: 3 reviews	1. There were no 4-lug TII wheels. Only base model S4's(86-88) were 4 lug. The lug patterns are 4x114.3 and 5x114.3. 2. The center bore on RX-7 wheels is too small for the 240SX hubs, therefore, the wheels will not fit.

05-16-2004, 03:41 PM	#4
richardxfeng Zilvia Addict Join Date: Jan 2003 Location: China Posts: 675 Trader Rating: (0) Feedback Score: 0 reviews	sorry for hijacking the thread.i was wondering if Mazda have same size wheel nuts as toyota?thanks!

05-16-2004, 06:56 PM	#6
SilviaDriver Post Whore! Join Date: Jun 2002 Location: San Jose, CA Age: 39 Posts: 5,514 Trader Rating: (2) Rides Gallery: SilviaDriver Feedback Score: 2 reviews	RX7 = 240sx? if so, then this is the correct section =]

05-16-2004, 09:15 PM	#8
thelinja Zilvia FREAK! Join Date: Jul 2002 Location: New Jersey Posts: 1,466 Trader Rating: (3) Rides Gallery: thelinja Feedback Score: 3 reviews	Unless you bore the center a few mm's, no they won't fit.

05-16-2004, 09:39 PM	#9
boro240 Zilvia FREAK! Join Date: Jan 2003 Location: Tucson, AZ Age: 39 Posts: 1,324 Trader Rating: (0) Feedback Score: 0 reviews	also, do FCs have the same offset as FDs? cause FD wheels are +50.

05-16-2004, 11:34 PM	#10
thelinja Zilvia FREAK! Join Date: Jul 2002 Location: New Jersey Posts: 1,466 Trader Rating: (3) Rides Gallery: thelinja Feedback Score: 3 reviews	All FC wheels are +40.

05-17-2004, 09:42 AM	#14
thelinja Zilvia FREAK! Join Date: Jul 2002 Location: New Jersey Posts: 1,466 Trader Rating: (3) Rides Gallery: thelinja Feedback Score: 3 reviews	Boring out the center of a wheel seems like a pain in the ass. I suppose you could use a dremel with a carbide bit, but it would be hard to get it uniform. What wheels are these anyway? Because the only 4 lug FC wheel I can think of is the phone dial looking one and that wheel is 14x5.5".

05-17-2004, 03:37 PM	#15
YoungRookie Zilvia FREAK! Join Date: Mar 2003 Location: Geencastle, PA Age: 35 Posts: 1,068 Trader Rating: (3) Feedback Score: 3 reviews	The wheels look like the watanabe rs8, i have seen these on a 240z before too and they look good.I dont think they are stock rx7 wheels __________________ 92 Hatch, KA-T, T28, 12 PSI, FMIC, 3" TBE, EFI ECU, 440cc Inj, And more...

05-17-2004, 10:55 PM	#16
thelinja Zilvia FREAK! Join Date: Jul 2002 Location: New Jersey Posts: 1,466 Trader Rating: (3) Rides Gallery: thelinja Feedback Score: 3 reviews	Well, if it isn't a stock Mazda wheel, you should test fit it because chances are the center bore would fit the 240 hub.